Schmalz FXCB Quick Reference Manual
Flat suction cup
Hide thumbs
Also See for FXCB:
- Operating instructions manual (47 pages) ,
- Quick reference manual (61 pages)
Subscribe to Our Youtube Channel
Related Manuals for Schmalz FXCB
Summary of Contents for Schmalz FXCB
- Page 1 Innovative Vacuum for Automation Quick Reference Guide Flat suction cup FXCB/FMCB 30.30.01.01839/00 | 09.2018 www.schmalz.com...
- Page 2 Published by © J. Schmalz GmbH, 09.2018 This document is protected by copyright. J. Schmalz GmbH retains the rights established thereby. Reproduction of the contents, in full or in part, is only permitted within the limits of the legal provi- sions of copyright law.
- Page 3 Read the complete operating instructions thoroughly and keep them for later refer- ence. Switching components that are not explosion-proof Risk of fire and explosion ► The product must not be used in explosion risk areas. 30.30.01.01839/00 www.schmalz.com 3 | EN...
- Page 4 Personal injuries and damage to the system These operating instructions are specific to the items included in delivery from ► Schmalz. These operating instructions do not take into account any modifications to the system made by the customer. ► Use only the connections, mounting holes and attachment materials that have been provided.
- Page 5 Danger to the operator ► Adapt and wear appropriate personal protective equipment based on the task be- ing performed. ATTENTION Incorrect disposal of the system or individual components Environmental damage ► Disposal according to national guidelines. 30.30.01.01839/00 www.schmalz.com 5 | EN...
-
Page 6: Intended Use
The robot system, to which the customer’s system was attached, is responsible for the motion in the various axes. When being applied to the workpiece, the foam must be compressed by at least 50%. 6 | EN www.schmalz.com 30.30.01.01839/00... -
Page 7: Technical Data
Technical Data FXCB FMCB Integrated vacuum generation External vacuum generation Number of suction cells Optimal input pressure 5.5 bar Permitted pressure range 4.5 to 7.0 bar Max. 7.0 bar Maximum degree of evacua- tion Compressed air consumption 161.5 l/min Suction flow 525.9 l/min... -
Page 8: Items Included In Delivery
Use the included screws and safety washers to mount the gripper on the robot. The required tight- ening torque can be found in the operating instructions of the robot system. The system must be attached securely, taking the weight of the system and its maximum load- bearing capacity into account. 8 | EN www.schmalz.com 30.30.01.01839/00... -
Page 9: Pneumatic Connection
If you select a supply hose that is too small, the compressed air supplied to the pneumatic ele- ments will not be enough for optimal operation. Compressed air supply The gripper type FXCB requires 161.5 l/min of compressed air. The compressed air supply integrated into robots is generally not sufficient. Ventilation The openings along the housing of the gripper serve as outlets for the exhaust air from the ejectors (only FXCB). -
Page 10: Electrical Connection
Electrical Connection The connection for control of the solenoid valve (only FXCB) and the vacuum switch is made using an 8-pole M12 connector that is integrated into the housing. The installed valve and the valve switch are switched via PNP. - Page 11 The sealing plate must be compressed by at least 50% to ensure that the workpiece is securely gripped. Only FXCB: The gripper is reset to the “Suction” state by switching the “Suction OFF” pin (see chapter 5.4). In order for this to occur, there must be compressed air at the com- pressed air connection.
- Page 12 12 | EN www.schmalz.com 30.30.01.01839/00...
Need help?
Do you have a question about the FXCB and is the answer not in the manual?
Questions and answers