Assembly Instructions SMARTCASE S500 Step 1 Prepare the Chassis Open the chassis with two hands by putting some pressure on your thumbs to push the cover reward. rear i/o Now you can take the top cover off. After opening the chassis unpack the contents.
Assembly Instructions SMARTCASE S500 Overview of the content: Passive Cooler Active Cooler Mainboard You can choose optional between the active cooler and the passive cooler. In the further instructions, we use the passive cooler but you go the same way for the active cooler.
Assembly Instructions SMARTCASE S500 Step 2 Mount the Cooler Before mounting the board into the chassis, it is necessary to add hardware to it first (CPU, Cooler, RAM, plus any optional additional hardware). First start with the back plate, which is essential for the cooler.
Assembly Instructions SMARTCASE S500 Next, mount the cooler on top of the CPU (1) and tighten the screws in the designated holes (2). Recommended mounting screw torque: max. 0.8Nm. Be aware that the wire needs to be able to reach the red slot.
Assembly Instructions SMARTCASE S500 Step 3 Insert Modules In the following picture, you can see the board with the three appropriated M.2 WLAN Modules or storage: Memory M.2 2230 WLAN M.2 2242 SSD/ Storage M.2 SSD / Storage 2280 Mainboard Next put the memory in tilted upwards and then push it down with a little pressure.
Assembly Instructions SMARTCASE S500 WLAN - Module / M.2. Module mounting First, you have to remove the screws. __________________________________________________________________________________________________________________________________________________________ Page 7 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Option 1: M.2. WLAN 2230 and SSD / Storage Insert WLAN card transversally into the slot (while paying attention to the coding / notch). Both modules, as shown in the picture, always tackle on the outer edges.
Assembly Instructions SMARTCASE S500 If all screws are tighten up, the finished result should look like this: Option 2: SSD / Storage Module Now you have to put in the M.2. SSD / Storage 2280 and M.2 2242. Pay attention to the notch!
Assembly Instructions SMARTCASE S500 In this case you only have to use one screw. So tighten up this screw in the next step. The finished result should look like this: __________________________________________________________________________________________________________________________________________________________ Page 10 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Step 4 MB-Mounting in Chassis Start by putting all the connectors on the board through the designated holes in the chassis. There are two different way to install the MB: 1. Swing in and push forward.
Assembly Instructions SMARTCASE S500 2. Put MB in position and push forward. The MB needs to be carefully moved and not touching the mounting panels (red circles). Put this part back on the chassis. Now push down the board so that the holes on the board fit onto the screw holes on the chassis.
Assembly Instructions SMARTCASE S500 In the next step, use the screws for the mounting holes on the edges (red marked). It should look like this now: __________________________________________________________________________________________________________________________________________________________ Page 13 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Step 5 Optional Mounting Mounting WLAN-antennas (optional) Please check the color-coding of the antennas. On the front side the bays of the antennas are firmly defined and marked with black and gray. Push the antenna cables completely through the opening in the housing and pay attention to the guide nose (red circle).
Assembly Instructions SMARTCASE S500 Mounting USB Type C (optional) First, put the blue end in the belonging connector on the mainboard and push it down with some pressure. __________________________________________________________________________________________________________________________________________________________ Page 15 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 In the second step, you place the front part at an angle back on the chassis and push it (red arrow). __________________________________________________________________________________________________________________________________________________________ Page 16 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Now bend the USB Cable as seen in the picture below and keep it to the appropriated holes. Afterwards you fix it by screwing the bolts in the designated holes. Afterwards slide the cover on the top of the chassis and screw the holes as explained in Step 6.
Assembly Instructions SMARTCASE S500 Mounting COM Cable (optional) For this option have a look at the attached “Assembly instruction for COM Cable with a D3544”. __________________________________________________________________________________________________________________________________________________________ Page 18 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Step 6 Close the Chassis Slide the cover on top of the board and chassis pushing it forward. Use some pressure to close it all the way. __________________________________________________________________________________________________________________________________________________________ Page 19 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 The last step to close the chassis is to put the screws in the designated holes and tighten them up. __________________________________________________________________________________________________________________________________________________________ Page 20 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Now your chassis is completely assembled. __________________________________________________________________________________________________________________________________________________________ Page 21 of 23 www.fujitsu.com...
Assembly Instructions SMARTCASE S500 Step 7 Add Stands For this step, you need two stands and four screws. There are two possible positions for adding the stand. You can you add them either on the bottom of the chassis or on the side of the chassis.