Page 1
TeamPad500 System User's Guide Revision 1.00.00 March 27, 2001 P/N 90000455...
Page 2
TeamPad 500 User’s Guide Revision History Revision Number Date Description of Change 1.00.00 2-1-2001 Original Release Copyright 2001 by Fujitsu-ICL Systems Inc. 2 of 47...
Page 3
Windows CE 2.12.It is assumed that the user has knowledge of the features and functionality of Windows CE. Windows, Windows CE, Visual C++, and Visual Basic are registered trademarks of Microsoft Corporation in the U.S. and other countries. Copyright 2001 by Fujitsu-ICL Systems Inc. 3 of 47...
Alpha Keyboard Pop-up ..........41 Low Main Battery Warning ..........42 Low Sub Battery Warning ..........43 Restoring the Application ..........44 Touch Panel Calibration ..........45 Date and Time Settings ..........46 Restore/Re-Initialize the Application ........47 Copyright 2001 by Fujitsu-ICL Systems Inc. 4 of 47...
Page 5
F1-F5 keys Function keys. Use these keys to perform special operations. Backlight key. Key (+/-) This key is used to adjust the contrast (“+” for more contrast and “- “ for less contrast). Copyright 2001 by Fujitsu-ICL Systems Inc. 5 of 47...
Page 6
When tapping the screen, use your finger or a dedicated accessory stylus (a pen for tapping). Do not use a tool with a sharp edge in place of the dedicated stylus, as this may damage the panel. Copyright 2001 by Fujitsu-ICL Systems Inc. 6 of 47...
When turning on the power for the first time, or after a hard reset (ie both batteries removed) a check is made on the equipment. If the unit has never been installed and configured through the “Setup Menu” the following equipment check screen is displayed. Copyright 2001 by Fujitsu-ICL Systems Inc. 7 of 47...
To begin the startup procedure: Hold down the ENT/SYS key, then press the “1” Key to Start the Touch panel calibration. To stop the startup procedure: Turn off the power by pressing the power key. Copyright 2001 by Fujitsu-ICL Systems Inc. 8 of 47...
Do not use an item with a sharp edge, such as a pencil or ballpoint pen, for tapping the screen, as this may damage or break the screen. Do not place the palm of your hand on the screen when tapping it. Copyright 2001 by Fujitsu-ICL Systems Inc. 9 of 47...
[4] OK and Apply Button Register the date and time that you have set and proceed to Section 3. [5] X button Cancel the date & time process and proceed to Section 3. Copyright 2001 by Fujitsu-ICL Systems Inc. 10 of 47...
[6] TeamPad Explorer. For details, refer to Section 3.7. [7] Running a program. For details, refer to Section 3.8 [8] Run the defined startup program (if any) in debug mode. For details refer to Section 3.9. Copyright 2001 by Fujitsu-ICL Systems Inc. 11 of 47...
The date and time can be updated. For details, refer to Section 3.2.4 [5] Input Panel Properties Change the Screen Pop-up keyboard size. For details, refer to Section 3.2.5. [6] X Button Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 12 of 47...
Do not update the memory area unnecessarily. Retain the default state. Otherwise, an application program may not be able to run. The memory area will return to the default state when data is erased in memory because of a dead battery. Copyright 2001 by Fujitsu-ICL Systems Inc. 13 of 47...
[2] is checked. [4] OK Button Apply the new Power Management Settings and return to the Control Panel. [5] X Button Cancel the Power Management changes and return to the Control Panel. Copyright 2001 by Fujitsu-ICL Systems Inc. 14 of 47...
OFF feature is enabled. It is enabled at factory shipment and configured for 10 minutes. [3] OK Button Apply the new Backlight Settings and return to the Control Panel. [4] X Button Cancel the Backlight Setting changes and return to the Control Panel. Copyright 2001 by Fujitsu-ICL Systems Inc. 15 of 47...
[4] OK and Apply Button Register the date and time that you have set and proceed to Section 3. [5] X button Cancel the date & time process and proceed to Section 3. Copyright 2001 by Fujitsu-ICL Systems Inc. 16 of 47...
Change the Screen Input Panel keyboard size. When tapped, the following window will be displayed. [2] OK button Register the Input Panel Changes and return to the Control Panel. [3] X button Cancel the Input Panel process and return to the Control Panel. Copyright 2001 by Fujitsu-ICL Systems Inc. 17 of 47...
Page 18
SIP will be displayed with the smaller keys. [3] OK button Register the Input Panel Changes and return to the previous Window. [4] X button Cancel the Input Panel process and return to the Previous Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 18 of 47...
CONFIG.HHT process, please refer to the “TeamPad 500 Programmer’s Reference Guide”. [1] Next Button Continue the Application Installation process. [2] Cancel Button Cancel the Application Installation Process. Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 19 of 47...
Page 20
Finishes the Application Installation process, and returns to the “Setup Menu”. Important When installing an application program, it’s best to initialize the system to a known state. See Section 3.4.1 for more details. Copyright 2001 by Fujitsu-ICL Systems Inc. 20 of 47...
Continue the Initialize Process. [3] OK button Return to the “Setup Menu” and do not process the Initialize. [4] X button Return to the “Setup Menu” and do not process the Initialize. Copyright 2001 by Fujitsu-ICL Systems Inc. 21 of 47...
Page 22
Initialize to default settings. A progress bar will be displayed while the function is running and at completion, will return to the previous Window. [2] No Button Cancel the Initialize Process. Return to the Previous Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 22 of 47...
Add or Modify a Launcher key. Go to the next Window. [2] Delete Button Deletes an existing Launcher key definition. [3] OK button Return to the “Setup Menu”. [4] X button Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 23 of 47...
Page 24
[3] Browse Button Browse the system to locate an application to assign to the selected launcher key [4] Cancel Button Cancel the Launcher Edit key process. Return to the previous Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 24 of 47...
[1] “Select BackUp or Restore” box Continue the Backup or Restore Registry function. Continue to the next Window. [2] OK button Return to the “Setup Menu”. [3] X button Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 25 of 47...
Page 26
Browse the system to locate destination of Backup or Restore File. [3] OK Button Accept the Registry Backup or Restore file destination. When complete return to the previous Window. [4] X button Return to the previous Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 26 of 47...
Return to the “Setup Menu”. Remember For details on operations when key combinations are pressed, refer to Section 4. Except for the task bar display, operations are set to enabled at factory shipment. Copyright 2001 by Fujitsu-ICL Systems Inc. 27 of 47...
Locate another storage area, other than Storage Card 1 or 2. [4] OK button Continue Backup or Restore Operation. Continue to next Window. [5] Cancel button Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 28 of 47...
Page 29
On a restore operation, instead of returning to the “Setup Menu”, the equipment powers off. On the next power on, the application will restart. The application is restored to the settings from the last backup operation. Copyright 2001 by Fujitsu-ICL Systems Inc. 29 of 47...
[1] “+” Used to expand the sub keys. [2] X button Close the Registry Editor and return to the “Setup Menu”. [3] File Dropdown Menu Proceed to the next Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 30 of 47...
Page 31
Delete a Registry key. [4] Register or Un-register Register or Un-register a DLL to the system. [5] Version Display the version number of the Registry Editor. [6] Close Close the Registry Editor. Copyright 2001 by Fujitsu-ICL Systems Inc. 31 of 47...
[1] Listing Folders and files are listed. Double-tap the folder name to display the folder list. Double tap a file (execution format file: extension EXE) to run the file. Copyright 2001 by Fujitsu-ICL Systems Inc. 32 of 47...
Page 33
New folder creation button: Creates a new folder in a specified list. [3] File Dropdown Menu Proceed to the next Window. [4] X button Close the TeamPad Explorer and return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 33 of 47...
Page 34
Displays the available free space in the Object Store and Storage Card(s). [6] Version Displays the Version of the TeamPad Explorer. [7] Exit Exit TeamPad Explorer. Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 34 of 47...
Opens a file browser dialog box. A program name can be selected from the dialog box. [3] OK button Run the program whose file name was entered. [4] Cancel button Cancel the Run program selection. Return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 35 of 47...
Select this button to enter Debug Mode. Unit will restart. If a startup program is defined, that program will launch, otherwise equipment will go to the Windows CE desktop. [2] No button Select this button to return to the “Setup Menu”. Copyright 2001 by Fujitsu-ICL Systems Inc. 36 of 47...
The main battery is low (25%) . It must be charged or replaced. - Unknown: The operational state of the battery cannot be checked. b. Percentage of the battery power left Displayed as a percentage. [2] Sub battery a. Status Copyright 2001 by Fujitsu-ICL Systems Inc. 37 of 47...
Page 38
If the sub battery must be replace, make sure the main battery has sufficient power to hold the state of the unit while the sub battery is replaced. Copyright 2001 by Fujitsu-ICL Systems Inc. 38 of 47...
To adjust the Volume, press the “1” key. The sound volume can be adjusted to one of four levels. Tap the desired sound volume level. A sample sound will be emitted on the tap. [1] OK button Register the Sound Volume. Return to the Battery Status Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 39 of 47...
When all the positions have been tapped, the target ceases to be displayed and the following message appears: "Press the ENT key to accept the new setting". Press the ENT key to register the calibration data and return to the Battery Status Window. Copyright 2001 by Fujitsu-ICL Systems Inc. 40 of 47...
Hold down the SFT key and press the F5 key to open the screen keyboard. It will open in the lower portion of the LCD display. Tap the desired character. To close the screen keyboard, hold down the SFT key and press the F5 key. Copyright 2001 by Fujitsu-ICL Systems Inc. 41 of 47...
If the sub battery must be replaced, make sure the main battery has sufficient power to hold the state of the unit while the sub battery is replaced. Copyright 2001 by Fujitsu-ICL Systems Inc. 42 of 47...
If the sub battery must be replaced, make sure the main battery has sufficient power to hold the state of the unit while the sub battery is replaced. Copyright 2001 by Fujitsu-ICL Systems Inc. 43 of 47...
To begin the restore procedure: Hold down the ENT/SYS key, then press the “1” Key to start the Touch Panel calibration. To stop the restore procedure: Turn off the power by pressing the power key. Copyright 2001 by Fujitsu-ICL Systems Inc. 44 of 47...
Do not use an item with a sharp edge, such as a pencil or ballpoint pen, for tapping the screen, as this may damage or break the screen. Do not place the palm of your hand on the screen when tapping it. Copyright 2001 by Fujitsu-ICL Systems Inc. 45 of 47...
[4] OK and Apply Button Register the date and time that you have set and proceed to Section 3. [5] X button Cancel the date & time process and proceed to Section 3. Copyright 2001 by Fujitsu-ICL Systems Inc. 46 of 47...
Startup Program. [2] Re-install the Application When restore is complete, an end-of-operation message is displayed and the equipment will re-start and run the Setup Menu and Configuration procedure. For details, see Section Copyright 2001 by Fujitsu-ICL Systems Inc. 47 of 47...
Need help?
Do you have a question about the TeamPad500 System and is the answer not in the manual?
Questions and answers