Toa MX-601 Operating Instructions Manual

Toa MX-601 Operating Instructions Manual

Hide thumbs Also See for MX-601:

Advertisement

All manuals and user guides at all-guides.com
Operating Instruction Manual
POWERED MIXER
Model MX-601
Toa Electric Co., Ltd.
KOBE, JAPAN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MX-601 and is the answer not in the manual?

Questions and answers

Summary of Contents for Toa MX-601

  • Page 1 All manuals and user guides at all-guides.com Operating Instruction Manual POWERED MIXER Model MX-601 Toa Electric Co., Ltd. KOBE, JAPAN...
  • Page 2: Table Of Contents

    The connectors are wired as follows. The pin 1 is ground (shield,) the pin 2 cold (low, minus), the pin 3 hot (high, plus.) 2. Description of components and functions on the MX-601 Various descriptions are applied, depending on each manufacturer. In our Operating and Instruction Manual explanation of components and functions is made according to our usage for them.
  • Page 3: General Description

    "on the road" applications. The MX-601 features 6 input channels; 1 program, 1 foldback, and 1 effects output. The internal power amplifier is rated at 120 watts into 8 ohms, 200 watts into 4 ohms, and 300 watts into 2 ohms load.
  • Page 4: Front Panel [Names Of Components & Their Usage]

    AUX/TAPE input pedance of 1k ohms. The output level of the MX-601 Please refer to fault protection signal should be decreased until the table on page 7 for full explana- LED only flashes intermittently.
  • Page 5: Rear Panel [Names Of Components & Their Usage]

    Operation of the MX-601 with proper grounding tech- plying power to the unit. ing improper fuses will also void the warranty The MX-601 should al- niques will result in less system noise and greatly reduced Caution - The MX-601 should ways be disconnected from AC outlet prior to changing fuses If fuse shock hazard.
  • Page 6: Connection Examples

    All manuals and user guides at all-guides.com Connection Examples Low Z input should be connected with low impedance (50 ohm ~ 600 ohm) microphone SUB MIXER (MX-601) Built in Power Amplifier for Foldback From Speaker Jack on Rear Panel WIRELESS TUNER...
  • Page 7: Input Connections

    As is described in the beginning of the Operating Instructions Manual, the connectors of the MX-601 are wired as follows: Pin 1 is ground (shield). Pin 2 is cold (low, minus). Pin 3 is hot (high, plus).
  • Page 8: How To Get A Good Mix

    If the impedances and levels do not match, mixing will be very difficult and the S/N ratio will also be adversely affected. Each input channel of the MX-601 is provided with a TRIM control. Thorough understanding of the function of a TRIM control will make mixing easier.
  • Page 9: Block And Level Diagrams

    All manuals and user guides at all-guides.com Block and Level Diagrams BLOCK DIAGRAMS LEVEL DIAGRAM — 8 —...
  • Page 10: Specifications

    All manuals and user guides at all-guides.com Specifications MIXER SECTION Frequency Response INPUT to FB out 59dB +0, -3dB 30Hz~20kHz (HIGH Zinput TRIM at "-30" position.) INPUT to REC out 45dB INPUT to GEQ out 59dB Total Harmonic Distortion AUX to PGM out 24dB 0.05% +4dBm at 1kHz.
  • Page 11: Characteristics Diagrams

    All manuals and user guides at all-guides.com Characteristic Diagrams HIGH Z IN. TRIM/MIN. & INPUT EQ POWER AMP POWER BAND WIDTH POWER AMP TOTAL HARMONIC DISTORTION POWER AMP COMPRESSOR REVERBERATION FREQUENCY RESPONSE Appearance — 10 —...
  • Page 12 All manuals and user guides at all-guides.com...

Table of Contents