Advertisement
Quick Links
Introduction
This Quick Start Guide describes how to set up Zilog's Z8 Encore! XP 8-Pin Development
Kit and start using it to build designs and applications that will employ the F042A Series
of 8-pin MCUs.
Kit Contents
Hardware
Hardware requirements include:
•
Z8 Encore! XP F042A Series 8-Pin Development Board, Z8F04A08100KITG
•
USB Smart Cable for connecting the PC to Z8 Encore! XP F042A Series Develop-
ment Board
•
5 V DC Universal Power Supply
Software (on CD-ROM)
Software requirements include:
•
Zilog Developer Studio II (Zilog Developer Studio II) – Z8 Encore!
Development Environment (IDE)
•
Full ANSI C-Compiler included
•
Sample Code
•
Acrobat Reader
•
Document Browser
Documentation
The Z8 Encore! XP Technical Documentation (on CD-ROM) include:
–
Development Kit User Manual
–
Zilog Developer Studio II – IDE User Manual (UM0130)
–
eZ8 CPU User Manual (UM0128)
–
Product Specification
Z8 Encore! XP F042A 8-Pin
Development Kit
Quick Start Guide
®
Copyright ©2011 Zilog
www.zilog.com
, Inc. All rights reserved.
QS005506-0111
®
Integrated
Advertisement
Related Manuals for ZiLOG Z8 Encore! XP
Summary of Contents for ZiLOG Z8 Encore! XP
- Page 1 Quick Start Guide QS005506-0111 Introduction This Quick Start Guide describes how to set up Zilog’s Z8 Encore! XP 8-Pin Development Kit and start using it to build designs and applications that will employ the F042A Series of 8-pin MCUs. Kit Contents...
-
Page 2: Configuring The 5 V Dc Universal Power Supply
– Product Brief – Product Line Card Requirements Table 1 lists the system requirements for running Zilog Developer Studio II. Table 1. Zilog Developer Studio II System Requirements Recommended Configuration Minimum Configuration • Windows XP Professional SP3 or later • Windows XP Professional •... -
Page 3: Setting Up The Development Board
Setting Up the Development Board The USB Smart Cable connects the target Z8 Encore! XP development board to a high- speed or full-speed USB port on your ZDS II host system. Always use a grounding strap to prevent damage resulting from electro- Caution: static discharge (ESD). - Page 4 To run the kit in DEBUG mode, follow the steps as described in Getting Started Using ZDS II on page 8. For complete details on jumper settings for Z8 Encore! XP MCU 8- pin development kits, refer to the Z8 Encore! XP F042A Series 8-Pin Development Kit User Manual (UM0187).
- Page 5 Z8 Encore! XP F042A 8-Pin Development Kit Quick Start Guide 1. Connect the USB Smart Cable to the host PC. dialog box The Found New Hardware should activate automatically. 2. Select Locate and install driver software (recommended) . The User Account Con- window is displayed;...
- Page 6 1. Connect the Zilog USB device to the Host PC. The Wizard Found New Hardware should activate automatically after connecting the Zilog USB device for the first time; select if asked to connect to Windows Update. No, not at this time 2.
- Page 7 1 on the target connector (see Figure 1 on page 3 for the location of pin 1 on the Z8 Encore! XP 8-pin development board). Figure 2. Connecting the Six-Conductor Ribbon Cable to the USB Smart Cable Applying Power to the Development Board Observe the following steps to apply power to the development board: 1.
-
Page 8: Installing The Zds Ii - Z8 Encore! Software
Z8 Encore! XP F042A 8-Pin Development Kit Quick Start Guide 2. Slide Power switch S2 to the ON position. The Green 3.3 V DC LED illuminates, indi- cating that power is being supplied to the board. LEDs D2, D3 and D4 should blink in sequence, indicating that your board is running the preloaded demonstration software. - Page 9 Do not apply power to the development board unless the USB Smart Cable is connected both to the host PC and to the development board’s DBG port P3. 3. Run the Zilog Developer Studio II software. By default, the Zilog Developer Studio II program is located in the menu under Start ...
- Page 10 Z8 Encore! XP F042A 8-Pin Development Kit Quick Start Guide 5. Browse to the folder for the file, located by default in: Samples ledBlink.zdsproj c:\Program Files\Zilog\ZDSII_Z8Encore_<version_number>\Samples\ Z8F04XP_8Pin_ledBlink\src 6. Select the file and click . The initial Zilog Developer Stu- Open ledblink.zdsproj...
- Page 11 Z8 Encore! XP F042A 8-Pin Development Kit Quick Start Guide Figure 3. Zilog Developer Studio II Opening Screen 7. Select the correct debug tool using Project Settings Debugger Debug Tool For example, select when using the USB Smart Cable. Click USBSmartCable additional information on how to setup the debugger.
- Page 12 LEDs to blink in the opposite TEST direction. For more information about using Zilog Developer Studio II and building projects for your Z8 Encore! XP development kit, refer to the ZDS II – Z8 Encore! User Manual (UM0130).
-
Page 13: Troubleshooting Tips
The Z8 Encore! XP F042A 8-pin device on the development board may also be replaced with a Z8 Encore! XP F08xA or F0823 8-pin device for a more detailed chip evaluation. - Page 14 • Click the button. The Red and Yellow LEDs should blink in sequence. HyperTerminal should display the message. LED Lights... If the demo code still does not run, contact Zilog Technical Support at support.zilog.com. QS005506-0111 Page 14 of 15...
- Page 15 Z8, Z8 Encore!, and Z8 Encore! XP are registered trademarks of Zilog, Inc. All other product or service names are the property of their respective owners.