INDEX I. INSTALLATION INSTRUCTIONS Product Overview / Tools Required......................Page 1 Prepare Door and Jamb..........................Page 2 Adjusting And Installing Latch........................Page 3 Installing Exterior Assembly........................Page 4 Installing Interior Assembly........................Page 5-6 II. MOBILE APPLICATION INSTRUCTIONS Mobile App Installation & Use ........................Page 7 Connect to Lock / Lock Settings ......................
PREPARE DOOR AND JAMB NOTE: For installation on doors with pre-drilled holes skip to page 4. 1. TEMPLATE a. Cut out template printed on page 20 of this Manual (Figure 1a). b. Fold template and place on door 36” (915mm) from the ground as marked (Figure 1b). Figure 1a Figure 1b 2.
ADJUSTING AND INSTALLING LATCH NOTE: Latch is shipped with the backset set at 2-3/8” (60mm) Measure the backset (backset is distance between edge of the door and the center of Lock). TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET 2-3/8”...
INSTALLING EXTERIOR ASSEMBLY 6. INSTALLING THE EXTERIOR ASSEMBLY Work with the Door Open for easy access. To access the mounting plate, unpack the Interior Assembly and remove the battery cover by sliding the cover upward. Locate the screws holding the Mounting Plate to the Interior Assembly. Remove the screws to release the Mounting Plate from the Interior Assembly. a. Unpack the Exterior Assembly. Use care to not scratch the green circuit board during handling and installation.
INSTALLING INTERIOR ASSEMBLY 9. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY a. Use care to attach the Control Wire male plug to the Interior Assembly female socket connector (Figure 9a). b. Do not force the Control Wire male plug into the Interior Assembly female socket connector (Figure 9b). c. The Control Wire male plug has two alignment tabs on the smooth side of the plug which is the top of the plug (Figure 9c). d. The Control Wire male plug is inserted with the smooth side up into the Interior Assembly female socket connector (Figure 9d). Interior Wire Plug Figure 9a-d Connect...
Page 8
Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad will illuminate blue, and the Honeywell button will flash green twice to signify that it has received power (Figure 11a). NOTE: Do not touch the Keypad until the blue light turns off.
Administrative & Authorized Users APPLICATION SETUP OPTIONS After you have installed your Bluetooth Lock, download the free “Honeywell Lock” App on your smart phone using one of the following options: 1. Search “Honeywell Lock” in the App Store or Google Play Store.
CONNECT TO BLUETOOTH LOCK IMPORTANT: Your Bluetooth must be enabled and you must be within range of the lock. 1. Press any key on Lock to activate the Lock. (Digital keys are lit when activated). 2. Click the “+” icon on the start screen. 3. Select which type of lock you would like to add 4. Click on available lock 5. Follow prompts to name the device After you have connected the lock to the Bluetooth App, the Admin. Digital Passcode must be reprogrammed by going to the “Lock Setting”...
USING APP TO LOCK AND UNLOCK UNLOCK DOOR WITH THE APP 1. Open App, choose Lock and Touch App to Unlock Open App & Touch 2 Keys to Unlock LOCK DOOR WITH THE APP Open the App Click on the connected safe you wish to lock Press and hold the lock button until the safe has locked. AUTO LOCK If enabled in “Lock Settings”, it will automatically lock after 20 to 900 seconds.
SYSTEM SETTINGS Go to the Main menu by pressing the * icon at the top left corner of the screen. Select “System Settings” Select below settings as desired. PATTERN PASSWORD Create a pattern to unlock the App. Provides extra security BEEP ON UNLOCKING Mute or enable a sound when the door is unlocked VIBRATION...
ACCOUNT MANAGEMENT Go to the Main menu by pressing the * icon at the top left corner of the screen. Select “Account Management” Select below settings as desired. PROFILE PICTURE Click on the picture at the top of the page Change the picture associated with the account by clicking the icon NICKNAME Click on “Nickname”.
4. Input the mobile number, or email address you would like to send the Passcode to 5. Press “Send by email” or “Send by Msg. ” CREATE AND SEND EKEYS To send an eKey, the receiver must have a Honeywell App account. The operation will fail if the Receiver is not regis- tered, or the wrong information is input when sending an eKey. SENDING EKEYS 1.
MANAGE USERS Ensure that WiFi is connected and working in order to manage Users associated with a connected lock FREEZE A USERS’ EKEY Select the lock with the eKey you want to Freeze Select the in the bottom menu Select the User you would like to Freeze Select “Freeze”...
Page 16
MANAGE USERS CLEAR USER EKEYS Select the lock with the eKeys you want to clear Select the in the bottom menu Select the top right icon Select “Clear” Input your account password Confirm the action RESET USER EKEYS When you reset eKeys, all eKeys will be removed from the lock. Select the lock with the eKeys you want to reset Select the in the bottom menu...
Page 17
MANAGE USERS RESET PASSCODES When you reset eKeys, all eKeys will be removed from the lock. Select the lock the Passcode is associated with Select the in the bottom menu Select “Passcode” from the top tab Select the Dropdown icon Choose “Reset Passcode” from the top selections Input your account password 7. Confirm the action...
- Green light and beep c. 5 VERY IMPORTANT If you have connected the lock to the Honeywell e. Input time (20 - 900 seconds, and 00 to turn off) Lock Application, the default Passcode “1234” will no longer work; and you will have to use the - Green light and beep from the App, which should be changed after 2.
PROGRAMMING PHYSICAL KEYPAD 5. ADD ADMINISTRATOR To add the administrator you must use the App. Press any button on the keypad to wake up lock in order to connect. 6. CUSTOMIZE PASSCODES RECEIVED FROM THE APP a. Input the VERY IMPORTANT - Green light and beep In order to change a Passcode, the Passcode c. 1 must have been sent from the App, and used by the Receiver.
TROUBLESHOOTING Issue Solution Lock will not function • Check that all batteries are fresh high quality Alkaline Batteries. electronically. • Check for proper polarity (+ -) of all batteries. • Check that the Control Wire is attached to the Interior Assembly. Lock gives error signal when •...
CONSUMER ASSISTANCE EMAIL: LHLPCustomerService@LHLPinc.com WEBSITE: www.honeywellsafes.com ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-800-860-1677 Ext. 1801 (Toll Free) Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call. (Toll Free) Australia 0011-800-5325-7000 (Toll Free) Germany/New Zealand 00-800-5325-7000 (Toll Free) Other Countries XX*-310-323-5722 (Toll Charges Apply) XX*- Dial U.S. Country Code first CALL CENTER HOURS: US/Canada 8am – 5pm (Pacific**) Mon – Fri (Subject to change) CALL BACK HOURS: Other Countries 8am – 5pm (Pacific**) Mon – Fri (Subject to change) Pacific**- Local time in Los Angeles, CA, USA * Insert correct Country Code ** Local Time based on Los Angeles California USA INTERNATIONAL CALL BACK HOURS: If you need to speak with a consumer assistant and cannot contact us during the Call Center hours above, please send an email or leave a telephone message, including your Name, Telephone Number and the best time for us to contact you during the Call Back hours above and we will make our every effort to contact you and help answer any of your questions or concerns.
FCC COMPLIANCE Regulatory Compliance This product complies with standards established by following regulatory bodies: - Federal Communications Commission (FCC) This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause undesired operation IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
LH Licensed Products, Inc. may be brought by the original residential purchaser more than one (1) year after the cause of action has arisen. The Honeywell Trademark is used under license Manufactured by: from Honeywell International Inc. Honeywell LH Licensed Products, Inc. International Inc. makes no representations or 860 East Sandhill Avenue warranties with respect to this product.