1. Manuals
  2. Brands
  3. Roger Manuals
  4. IP Access Controllers
  5. PR411DR
  6. Installation manual

Roger PR411DR Installation Manual

Hide thumbs Also See for PR411DR:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Function Manual, Installation Manual
Roger Access Control System
Installation guide for
PR411DR/PR411DR-BRD Access Controllers
Firmware version: 1.18.6 or newer
Hardware version: 1.4
Document version: Rev. K
© 2016 ROGER sp. z o.o. sp.k. All rights reserved. This document is subject to the Terms of Use in their current version published at
the
www.roger.pl
website of the Roger sp. z o.o. sp.k. company (hereinafter referred to as ROGER).

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PR411DR and is the answer not in the manual?

Questions and answers

Related Manuals for Roger PR411DR

Summary of Contents for Roger PR411DR

  • Page 1 Hardware version: 1.4 Document version: Rev. K © 2016 ROGER sp. z o.o. sp.k. All rights reserved. This document is subject to the Terms of Use in their current version published at www.roger.pl website of the Roger sp. z o.o. sp.k. company (hereinafter referred to as ROGER).

  • Page 2: Table Of Contents

    2. Description and Specification ..................3 3. Installation ........................4 3.1 Terminals and connection diagram ..................4 3.2 Front panel ........................7 3.2.1 PR411DR controller ....................... 7 3.2.2 PR411DR-BRD controller ....................7 3.3 Power supply ........................8 3.4 Connection of door lock ....................10 3.5 Communication with controller ..................

  • Page 3: Introduction

    PR411DR type controller is single door access controller used in RACS 4 access control system. Both PR411DR and PR411DR-BRD versions are functionally identical, but differ mechanically. PR411DR is installed inside plastic enclosure fitted to mounting on DIN 35 mm rail, while PR411DR-BRD is just a PCB module without enclosure.

  • Page 4: Installation

    PR411DR Installation Guide Rev.K.doc 2016-10-28 PR411DR-BRD: IP20 Dimensions HxWxD PR411DR: 85 x 124 x 73mm PR411DR-BRD: 80 x 115 x 28mm Weight PR411DR: approx. 200g PR411DR-BRD: approx. 100g Certificates 3. I NSTALLATION 3.1 Terminals and connection diagram Fig. 1 PR411DR controller Table 2.
  • Page 5 PR411DR Installation Guide Rev.K.doc 2016-10-28 COM1 REL1 relay common terminal REL2 relay output (NC) Power supply for controller COM2 REL2 relay common terminal Fig. 2 PR411DR-BRD controller Table 3. PR411DR-BRD terminals Terminal Description Terminal Description BAT+ Backup battery Ground BAT-...
  • Page 6 PR411DR Installation Guide Rev.K.doc 2016-10-28 Fig. 3 Typical connection diagram for PR411DR controller 6/17...

  • Page 7: Front Panel

    Fig. 4 PR411DR front panel 3.2.2 PR411DR-BRD controller According to fig. 5, PR411DR-BRD is equipped with 5 LED indicators and RESET button (S1) on its PCB. RESET button can be used to restart the controller in the same way as in case of powering device off and then on.

  • Page 8: Power Supply

    Fig. 5 LEDs at PR411DR-BRD controller PCB 3.3 Power supply Basically, PR411DR and PR411DR-BRD controllers are designed for power supply from 230VAC/18VAC transformer with minimal power output 25VA, but they can also be supplied with 12VDC or 24VDC. The connection of power supply is shown in fig. 6, fig.7 and fig. 8.
  • Page 9 PR411DR Installation Guide Rev.K.doc 2016-10-28 Fig. 6 PR411DR controllers supplied with 18VAC Fig. 7 PR411DR controllers supplied with 24VDC 9/17...

  • Page 10: Connection Of Door Lock

    PR411DR Installation Guide Rev.K.doc 2016-10-28 Fig. 8 PR411DR controllers supplied with 12VDC General guidelines for 24VDC and 12VDC power supply  Negative (GND) potentials of power supply units must be connected with any wire.  It is not necessary to connect GND terminals of HRC series controllers.

  • Page 11: Communication With Controller

    3.6.1 PRT readers and XM-2 expander PR411DR controller can operate with two PRT series readers and XM-2 I/O expander – see fig. 10. Addresses of PRT readers must be ID=0 and ID=1 and the address of XM-2 expander must be ID=5.

  • Page 12: Prt And Third Party Readers (Wiegand)

    Wiegand reader does not work properly with the controller, it might be necessary to use PR-GP module. The PR-GP works as electrical interface between reader and controller. In order to determine if PR-GP might be useful, please contact Roger technical support. Fig. 11 Connection of Wiegand readers 3.7 Input and output lines...

  • Page 13: Inputs

    PR411DR Installation Guide Rev.K.doc 2016-10-28 3.6.1 Inputs All inputs (IN1..IN8) of controllers have identical electric structure and can be configured as NO or NC lines using PR Master software. The NO input is triggered by shorting it to supply minus (GND) while the NC input must be normally shorted to supply minus (GND) and it becomes triggered when connection with GND is interrupted.
  • Page 14 PR411DR Installation Guide Rev.K.doc 2016-10-28  During update of controller firmware by means of Roger ISP software (so called Fixed ID)  Manually during Memory Reset procedure  By means of PR Master software The first two methods enable configuration of hardware addresses while the remaining two enable configuration of software addresses.

  • Page 15: Memory Reset Procedure

    PR411DR Installation Guide Rev.K.doc 2016-10-28 4.1.3 Addressing during Memory Reset procedure Software address can be configured during Memory Reset procedure – see 4.2 Memory Reset procedure. Note: Software address is effective only if the address set with jumpers on the controller is in range of 100..127 and FixedID is None.

  • Page 16: Controller Programming

    4.4 Firmware update The latest versions of firmware and Roger ISP software are available at www.roger.pl. In order to update firmware it is necessary to connect the device by means of RS485 bus to communication interface (UT-2USB or RUD-1) and then connect the interface to PC with installed Roger ISP software.

  • Page 17: Product History

    PR411DR Installation Guide Rev.K.doc 2016-10-28 UT-4DR Ethernet-RS485 communication interface. UT-2USB USB-RS485 communication interface. RUD-1 Portable USB-RS485 communication interface with 12VDC/0.12A output. XM-2DR I/O expander. 6. P RODUCT HISTORY Table 7. Product history Product version Released Description PR411DR v.1.0 05/2011 The first commercial version of the product PR411DR v.1.1...

This manual is also suitable for:

Pr411dr-brd

Table of Contents