Advertisement
PRE-INSTALLATION
Remove accessory packaging and inspect shipment for dam-
age. See Table 2 for kit contents. File claim with shipping com-
pany if accessory is damaged or incomplete. Verify unit is level
and adjust if necessary.
Table 2 — Accessory Kit Contents
ACCESSORY
DESCRIPTION
PART NO.
30MP-900---036
Sound Blanket
30MP-900---038
Sound Blanket
38AP-900---009
Sound Blanket
38AP-900---010
Sound Blanket
38AP-900---025
Sound Blanket
Sound Blanket Cap
38AP-900---035
Sound Blanket
38AP-900---036
Sound Blanket
38AP-900---037
Sound Blanket
38AP-900---038
Sound Blanket
WARNING
To avoid the possibility of electrical shock, open all dis-
connects before installing or servicing this accessory.
INSTALLATION
The following are the procedures to install the low sound
compressor
blanket.
The
30RAP070-150, and 30MPA,MPW units without sound enclo-
sure do not have access panels.
1. Open and tag all disconnect locations to alert others not to
restore power until work is completed.
2. Remove access panel if applicable.
•
The 38APS,APD025-030, and 30RAP011-030 units
have one compressor access panel with one latch at
the top of the panel. See Fig. 1.
•
The 38APD040-060 and 30RAP035-060 units have 2
compressor access panels with one latch at the top of
each panel. See Fig. 2.
•
The 38APS040,050 units have one compressor access
panel with 2 latches at the top of the panel. See Fig. 3.
3. The access panel must be removed as follows:
a. If shipping screws are present, remove them from
sides of the panel.
b. To remove access panel, apply
screwdriver to slotted latches until panel releases.
See Fig. 1-3.
4. For 30MP units with sound enclosure panels, access the
compressors by removing the left side enclosure panel
(facing the front/control box end). See Fig. 4.
5. Wrap the sound blanket around the compressor:
a. For 30RAP011,016 units, wrap the sound blanket
around the compressor in counterclockwise direction.
b. For all other units, wrap the sound blanket around
the compressor in clockwise direction. See Fig. 5.
c. For 30MP040,045 units, install blanket on compressor
A3 by loosening control box retaining bolts, then care-
fully shifting control box outward to allow enough
space to access compressor A3. After securing the
QTY
PART NO.
2
30MP501334
2
30MP401891
1
38AP501670
1
38AP500286
1
38AP500191
1
00PSN500684300A
1
38AP504400
1
38AP505158
1
38AP505159
1
38AP505160
38APS065,
38APD070-130,
1
/
turn with flathead
4
blanket (see Steps 6, 7, 8, and 9) return control box to
original position (see Step 10).
IMPORTANT: Be sure to keep enough slack in the con-
trol wires when shifting the control box. It is recom-
mended that more than one person move the control box.
Properly support the control box when shifting it from its
original position.
CONTROL BOX
HINGED ACCESS
COMPRESSOR
SLOTTED LATCH
Fig. 1 — Compressor Access Panel with One
Latch — 38APS,APD025-030 and 30RAP011-030
SLOTTED LATCHES (2)
CONTROL BOX
HINGED ACCESS
CIRCUIT A
COMPRESSOR
ACCESS
Fig. 2 — Two Compressor Access Panels Each
with One Latch — 38APD040-060 and
30RAP035-060
2
ACCESS
a38-7214
a38-7215
CIRCUIT B
COMPRESSOR
ACCESS
Advertisement
