Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for FAAC C720
Summary of Contents for FAAC C720
- Page 1 C720-C721 C720-C721...
- Page 2 9) FAAC is not responsible for failure to observe Good warnings handbook supplied with the product. Technique in the construction of the closing ele-...
-
Page 3: Table Of Contents
Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY Declares that: Operator mod. C720 - C721 is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions of Directive 98/37/EC;... -
Page 4: General Remarks
C720 - C721 We thank you for choosing our products. We are certain that they will fully meet your needs with respect to the performance that have been designed for. These products have been designed and built to control vehicle access. AVOID ANY DIFFERENT USE. -
Page 5: Dimensions
Key-operated control ¿ ¿ Fig. 3 » » The dimensions and electrical preparations (standard system) are the same for operator C720 and for operator C721 5 INSTALLATION OF AUTOMATED SYSTEM 5.1 PRELIMINARY CHECKS To ensure safety and an efficiently operating automated system, make sure the following conditions are observed: •... -
Page 6: Masonry For Foundation Plate
Fig. 3. To facilitate the connections in the control unit, pull out the leads by at least 30 cm from the hole on the plate. Dimensions in mm Fig. 7 C720-C721 732568 - Rev.E... -
Page 7: Mechanical Installation
Position the operator on the foundation plate using the nuts and washers provided as shown in Fig. 9. During this operation, pass the cables though openings in the motor casing (see Fig. 9 re. Fig. 8 and Fig. 9 refer to operator C720 Fig. 9 Fig. -
Page 8: Installing The Rack
Couple another rack element and fit to the previous ele- ment. Move the gate manually and carry out the securing opera- tions as for the first element, thus proceeding until the gate is fully covered. Fig. 13 Fig. 14 Fig. 15 C720-C721 732568 - Rev.E... -
Page 9: Operational Start-Up
6.1.1 EARTHING Connect the earth cable as described in Fig.17. Fig. 17 Fig. 17 refers to operator C720 6.1.2 ELECTRONIC EQUIPMENT The electronic control equipment in the gearmotors is fastened to a mount (Fig. 18 re. -
Page 10: Positioning Of Limit Switches
(Fig. 21 re. Fully lower the release lever to the mechanical stop Fig. 21 Carry out the opening or closing manoeuvre manually. Fig. 20 Fig. 21 C720-C721 732568 - Rev.E... -
Page 11: Maintenance
Lowering the release lever, both the motor lock, which is retracted (Fig. 23 re. ), and the safety microswitch forcing the automation to STOP (Fig. 23 re. ) are operated. ³ ³ ³ · · · Fig. 25 Fig. 23 C720-C721 732568 - Rev.E... - Page 12 DESCRIPTION Carry out the opening or closing manoeuvre manually. The C720 and C721 automated systems are ideal for controlling vehicle access areas with average transit frequency. RESTORING NORMAL OPERATION The C720 and C721 automated systems for sliding gates are...
- Page 13 POLAND Saint Priest, Lyon - France FAAC POLSKA SP.ZO.O tel. +33 4 72218700 Warszawa - Poland www.faac.fr tel. +48 22 8141422 FAAC FRANCE - AGENCE PARIS www.faac.pl Massy, Paris - France RUSSIA tel. +33 1 69191620 FAAC RUSSIA LLC www.faac.fr...
Need help?
Do you have a question about the C720 and is the answer not in the manual?
Questions and answers
I have a newly installed C720 motor for a sliding gate. At what distance should the remote control work?
The effective range of the remote control for the FAAC C720 sliding gate motor is ≥ 50 meters in an open area.
This answer is automatically generated
I lost the key for the box of our FAAC gate opener and we can''t do it manually..What can I do?