Page 1
I N S T A L L A T I O N I N S T R U C T I O N S Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description OB1U...
AN ACCESSORY is the secondary Chief • bare 8" thick solid concrete or 8" x 8" x 16" concrete product which is attached to a primary Chief product, and may block wall; or have a component attached or setting on it.
Installation Instructions OB1U ASSEMBLY AND INSTALLATION Locate Mounting Site The OB1U will allow an interactive flat panel display to be installed over an existing chalkboard/whiteboard. The OB1U WARNING: IMPROPER INSTALLATION CAN LEAD TO has telescoping legs which allows it to be anchored above and MOUNT FALLING CAUSING SEVERE PERSONAL INJURY below the existing chalkboard/whiteboard.
Page 6
48" apart to accommodate three 24" steel NOTE: The OB1U may be attached to an 8" concrete wall or studs, and a minimum of 32" apart to accommodate an 8" x 8" x 16" concrete block wall. Do NOT install into three 16"...
Page 7
Installation Instructions OB1U Steel Stud Site Selection If back side of wall is unfinished, drywall must be installed to a minimum of one stud left and right of the stud(s) being used to install the mount. Drywall must be secured to studs with screws a maximum of 12" (305mm) apart down center of stud.
Page 8
OB1U Installation Instructions Snap off plastic straps on anchor at wall by pushing side to side, snapping off straps level with flange of plastic cap. (See Figure 10) Repeat Steps 5 through 8 for each mounting hole. (side view) Steel Stud...
Page 9
Fasten upright in place using one 1/4-20 x 3/8” button head Tighten the button head cap screws on the wall brackets to cap screw (B) and one 1/16” nylon spacer (D) [from OB1U fasten the wall assembly in place. (See Figure 12) Hardware kit] into slide nut.
Page 10
(See Figure 16) H1). Pull down on interface bracket handles to open for attaching NOTE: Use universal to OB1U. (See Figure 15) washer (H1) ONLY with M6 screws. Hang flat panel with attached interface brackets onto the cross bracket (X), ensuring that one interface bracket is on each side of the cross bracket center line (CL).
Page 11
BEFORE completing attachment to wall. Figure 17 NOTE: The lower part of the OB1U must be attached to the wall using the correct hardware for the wall type. It may Installing Wall Bracket Covers be attached to a wood or steel stud wall, or to a Open the lower flaps of the wall bracket cover (Q) outward.
Page 12
OB1U Installation Instructions Mark the wall over stud through the lower wall bracket (V) attached to each upright assembly (P). (See Figure 20) Drywall Drill one 1/8” pilot hole (wood studs) or 1/2" pilot hole (steel Plastic Straps studs) at each mark. (See Figure 20) Use two 1/4"...
Page 13
Installation Instructions OB1U 10. Use two 1/4-20 x 1-3/4” Phillips pan machine screws (I) and Adjust 4" knobs so that flat panel is supported evenly by two 1/4” flat washers (G) to attach each lower wall bracket each of the four bumpers. (See Figure 27) (V) to anchors in wall.
Page 14
OB1U Installation Instructions Adjustment of Lower Leg Plumb Turn the buttonhead screw at bottom of leg (if necessary) to adjust the plumb on lower leg so that it sets firmly against the wall. (See Figure 29) Figure 29...
Page 16
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Chief, a products division of Asia Pacific A Office No. 918 on 9/F, Shatin Galleria Milestone AV Technologies 18-24 Shan Mei Street...
Need help?
Do you have a question about the OB1U and is the answer not in the manual?
Questions and answers