Zublin Swiss Garde 360 Presence DALI Master A-Comfort 24m Installation Instructions Manual page 5

– Press push-button 0.1–0.5 s ¶ manual ON/OFF (toggle) at presence plus delay time
– Press push-button >2 s ¶ manual DIM (toggle up/down) at presence plus delay time (constant light control deactivated)
– Press push-button >10 s ¶ 2 h ON/OFF (toggle) plus delay time (in case of motion detection) only via 230 V push-button T1+T2
All zones may be manually switched on or off or dimmed via 230 V push-button or DALI input module. Whenever manual override is active, constant lighting control is deactivated and may be
reactivated as follows:
– Press «Auto» on the remote control (accessory, item no. 41934)
– Switch light off and on again via external push-button (T1+T2)
– Await delay time expiry (Time 1)
– Select Scene 15 which is programmed to an input of the DALI input module.
With the setting zone 3 = daylight zone (item 2.4) the push-button T3 has no function.
1.9 Use of DALI Input Module (7)
The DALI input module (accessory, item no. 70020) provides the possibility to select lighting scenes. The scenes must be defined via a DALI programming interface.
The presence detector remains active during motion detection plus delay time after scene selection (zones 1 to 4).
The function of the push-buttons is set via the group address i.e. the scene numbers of the DALI input module:
– Group 10 provides the same functionality as push-buttons 1+2
– Group 11 provides the same functionality as push-button 3
– Group 12 provides the same functionality as push-button 4
– Scene 15 resets the daylight group to AUTO mode
– Scenes 1–14 activates the respective scenes
If two push-buttons of the DALI input module (7) are programmed with the same group address,
the push-button programmed first will send only ON and the other push-button only OFF commands.
!
Other DALI commands such as Broadcast are not permitted.
Note: Lighting scenes programming is stored in the DALI ballasts. Remember to re-program scenes after the replacement of any DALI ballasts.
The number of DALI input modules is unlimited as long as the maximum current of 200 mA is not exceeded. Several DALI input modules may be configured for the same function, e.g. the control
of zone 4.
1.10 Operation and Maintenance
Lens pollution may impair the correct function of the detector. Therefore, the lens should be kept tidy and clean. Use a moist cloth and a little water together with standard cleaning agent. Do not
exert too much pressure on the lens. Should the lens or other components be defective, they will have to be replaced.
In case of failure and subsequent replacement of a single DALI ballast, its renewed allocation to a zone will not be necessary. The detector will automatically recognise and address the replace-
ment ballast. If two or more ballasts are defective, manual allocation of the replacement ballasts will be necessary.
1.11 Technical Data
Supply voltage 230 V / 50 Hz
Standby power 0,45 W
Switching power 2300 W / 10 A resistive (cos ϕ 1,0)
1200 VA / 5,2 A inductive (cos ϕ 0,5)
350 VA / 1,5 A LED
DALI devices 1–64
DALI power supply max. 200 mA
DALI cable length Ø 2.5 mm
Ø 1.5 mm
Ø 1.0 mm
Max. no. of Slave devices 10
Detection area 360°
Detection range Art.-Nr. 41750, 41751: max. Ø 6 m presence, approx. Ø 24 m at a height of 3 m
Art.-Nr. 41761: approx. Ø 24 m at a height of 6 m
Installation height Art.-Nr. 41750, 41751: 2–3,5 m
Art.-Nr. 41761: 3,5–8 m
Lux level control 100–2000 lx
Timer control 5 min to ∞
Standby lighting Off, 5 min to ∞, level 0.1 to 51%.
Protection class IP54
Temperature range -5 bis +50 °C
Dimensions Edition UP: Ø 100x46.4 mm (visible dimensions)
Edition AP: Ø 117.3x45.9 mm (visible dimensions)
Flush-mount drilling
Ø 90 mm
Colour
RAL9010
M. Züblin AG, Neue Winterthurerstrasse 30 , CH-8304 Wallisellen, www.zublin.ch
Installation instructions - Swiss Garde 360 Presence DALI Master A-Comfort 24 m
< 300 m
2
2 < 150 m
< 100 m
2
5
Züblin Elektro GmbH, Marie-Curie-Strasse 2, DE-79618 Rheinfelden-Herten, www.zublin.de
Art.-Nr. 41750, 41751, 41761 - Edition 8-2017