Zublin Swiss Garde 360 Presence DALI Master 16m User Manual
Hide thumbs
Also See for Swiss Garde 360 Presence DALI Master 16m:
- Installation instructions manual (17 pages) ,
- Quick manual (12 pages)
Advertisement
Quick Links
User manual
360° sensor.
Swiss Garde 360 Presence
DALI Master 16m
Swiss Garde 360 Presence
DALI Master RA 16m
Swiss Garde 360 Presence
DALI Master 30m
Swiss Garde 360 Presence
DALI Master RA 30m
Art.-Nr. 26001, 26002, 26003, 26004
available
accessories:
DALI remote
Advertisement
Related Manuals for Zublin Swiss Garde 360 Presence DALI Master 16m
Summary of Contents for Zublin Swiss Garde 360 Presence DALI Master 16m
- Page 1 User manual 360° sensor. Swiss Garde 360 Presence DALI Master 16m Art.-Nr. 26001, 26002, 26003, 26004 available accessories: Swiss Garde 360 Presence DALI Master RA 16m DALI remote Swiss Garde 360 Presence DALI Master 30m Swiss Garde 360 Presence DALI Master RA 30m...
- Page 2 Important informations - Work on the mains may only be carried out by specialists. -The installation must be carried out in accordance with the national standards. - Disconnect the 230 volt power supply each time before starting to install! -The detector is always supplied with a fuse (250VAC, 10A) Type C, to be provided as a protective measure in accordance with EN60898-1.
- Page 3 Wiring Standard installation; Optional "S" connection for connecting slave detectors; Optional button connection "R" or T1 / T2 for manual switching on or off or dimming of the light Push button function Light on / off: press button for approx. 1 second (On / off duration = last acquisition + set time) Dimming: Press and hold the button for>...
- Page 4 VR’s LED, flashes 1x when it is detected, 3x when a command has been received from the handheld transmitter. Zubehör: DALI Handsender. Caution! The values can be set on the detector using a controller or DALI handheld transmitter. If a detector has been set using a hand transmitter, each controller can be activated individually by re-setting the respective controller, or all controllers together using the reset button on the hand transmitter (see instructions for use of the hand...
- Page 5 LUX (twilight sensor) The twilight sensor regulates the response threshold (light value) of the detector, from which the detection is activated, and specifies the mixed light value for constant light control. Turning towards the moon (approx. 5 lux) means that the sensor only switches on the light when it is dark (max, 2000 lux, maximum lighting, daylight control over the whole range!).
- Page 6 Detection range The 360 ° all-round detection area and the dense detection network guarantee optimal function. The range depends on the mounting height and walking direction. As the detector detects the temperature difference between If the heat source and the ambient temperature react, the range can vary depending on the situation at the installation site (floor heating, etc.).
- Page 7 Troubleshooting Problem Cause / Redemption Lamp does not turn on: - Twilight value set too low - Check the lamp from the lamp - Check mains voltage / fuse Turns on without reason -Check the detection area for sources or does not turn off: which may causes detections: (draft, animals, heating, etc.) can cause incorrect switching...
- Page 8 Niko Schweiz AG, Leutschenbachstrasse 95, CH-8050 Zürich Niko Deutschland GmbH, Warmbacher Strasse 80, DE-79618 Rheinfelden Niko nv, Industriepark West 40, BE-9100 Sint-Niklaas www.niko.eu/zublin Art.-Nr. 26001, 26002, 26003, 26004...