Zublin Swiss Garde 360 Presence DALI Master A-Comfort 24m Installation Instructions Manual page 10

2.18 Multi-zone (13)
Luminaires in the CLC daylight group that are allocated to multi-zone 4 can also, as for a secondary zone, be overridden using push-button T4 (CLC is then deactivated).
In the case of manual push-button operation, the previously pressed button will determine the mode activated for the multi-zone. In the case of on/off operation with push-button T4, the multi-zone
will behave like a secondary zone without CLC.
After 2 short presses of push-button T1&2, the multi-zone will switch back to the daylight group with active CLC.
Select luminaire
Lock/
〉 〉 with «Next» 〉
Init.
Unlock
push-button
Note: Multi-zone is only possible in modes 1 to 3.
3. STATUS CHECK
Use «Status» to display the state of individual parameters on the presence detector. Parameters are only displayed in operating mode.
Status display is indicated by flashing LEDs. Await the flashing signal before performing other remote control activites.
If no LED is activated, the detector is not initialized.
3.1 Status – Time (4)
Press «Status» followed by «Time» to display individual time settings.
– Time 1: delay time lighting
– Time 2: HVAC
– Time 3: cut-off
– Time 4: standby lighting
Depending on what time status should be displayed, press «1» for Time 1 or «4» for Time 4. The presence detector displays the set time by the respective number of LED flashes.
Time (min) 5 10
Number of flashes, green 1
Example: Display lighting delay time 1: Press «Status» followed by «Time» and «1». The green LED flashes three times, indicating that the delay time is set to 15 min.
3.2 Status – Lighting Output
«Press Status» followed by «Lux» to display LUX level setpoint. The presence detector displays the LUX level setpoint by the respective number of LED flashes.
Lux (lx) 100 200
Number of flashes, green 1
Example: Display LUX level setpoint: Press «Status» followed «Lux». The green LED flashes three times, indicating that the LUX level setpoint is set to 300 lx.
3.3 Status – Sensitivity
Press «Status» followed by «Sens.» to display sensitivity. The presence detector displays the sensitivity by the respective number of LED flashes..
Sensitivity Maximum
Number of flashes, green 1
Example: Press «Status» followed by «Sens». The green LED flashes twice, indicating that the sensitivity is set to high.
3.4 Status – Burn-in
Press «Status» followed by «Burn-in». The presence detector displays the remaining burn-in time in 10 hour intervals by the respective number of LED flashes.
A red LED indicates inactive burn-in.
Burn-in ≤10 h
Number of flashes, green 1
Example: Press «Status» followed by «Burn-in». The green LED flashes twice, indicating that the remaining burn-in time is 20 h.
M. Züblin AG, Neue Winterthurerstrasse 30 , CH-8304 Wallisellen, www.zublin.ch
Installation instructions - Swiss Garde 360 Presence DALI Master A-Comfort 24 m
Lock/
〉 〉 etc. 〉
4 Next
Unlock
15 30 45 60 ∞
2 3 4 5 6 7
300 400 600 800 1000 2000
2 3 4 5 6 7
High Low Minimum
2 3 4
≤20 h ≤30 h ≤40 h ≤50 h
2 3 4 5
OFF
8
user defined
8 9
≤60 h ≤70 h ≤80 h ≤90 h
6 7 8 9
10
Züblin Elektro GmbH, Marie-Curie-Strasse 2, DE-79618 Rheinfelden-Herten, www.zublin.de
Art.-Nr. 41750, 41751, 41761 - Edition 8-2017
≤100 h
10