Related Manuals for Pakedge Device & Software SE-8P2-EP
Summary of Contents for Pakedge Device & Software SE-8P2-EP
- Page 1 SE-8P2-EP 8 Port PoE Plus Powered Gigabit Ethernet Switch with Two PoE Pass-through ports or Four PoE Pass-through ports with AC adapter User Manual – Version 1.0...
-
Page 2: Fcc Certifications
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 3 products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies.
-
Page 4: Unpacking Information
Unpacking Information Thank you for purchasing this product. Before installation, please verify that your package contains the following items. 1. One Gigabit Ethernet High-power PoE Pass- through Switch 2. Rubber feet *4 3. User’s Manual 4. One DC power adapter (optional) 5. - Page 5 power on the 4 PSE ports for connected devices via CAT 5 or above twisted cables. By integrating the data transmitting cable and power cord, it eliminates the effort constructing your network. You can easily connect a Wireless AP or a VoIP phone (PD devices) to this switch without installing outlets for them.
- Page 6 Supports 128K Bytes frame buffer Non-blocking switching performance Supports IEEE 802.3x back-pressure flow control for full duplex Supports 802.3az Energy Efficient Ethernet Supports Green Ethernet (Link-On Cable Length Power Saving and Link-Down Power Saving) Operation Temperature: 0~40℃...
- Page 7 LED Definition LED indicators for the device Feature Description The switch is powered by the external PWR LED power adapter (DC 48V). The switch is powered by the PD port. PD LED (high-power 60W). It indicates the PoE connection status of the port 1 to port 4.
- Page 8 rear panel. All Ethernet ports feature 10/100/1000 Mbps with auto-negotiation and auto MDI-X. The rear panel of the switch is shown as below: The rear panel port description Feature Description Power The DC 48V power adapter is optional if DC 48V local network could supply power to PD port 10/100/1000Mbps...
-
Page 9: Installation
Four class 2 PD devices (4x7W) or Three class 1 PD device and One class 2 PD devices (3x4W +1x7W) Tw o c l as s 1 P D de v i c e a n d Tw o c l as s 2 P D de v i c e s (2 x 4W + 2 x7W ) ... - Page 10 Install the switch on a level surface that can support the weight of the unit and the relevant components. Plug the switch with the Ethernet Cable on the PD port, which is connecting to a PSE or Plug the female end of the power adaptor on DC Jack to get power.
-
Page 11: Product Specifications
Ports that 10/100/1000 Category5,5e,6 support PoE Mbps UTP/STP or (Port 1~4) above Product Specifications IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3ab 1000BASE-T IEEE802.3x flow control Standard IEEE802.3at/af PoE standard (DTE power via MDI) IEEE802.3az Energy Efficient Ethernet 8 * 10/100/1000 Mbps auto MDI/MDI- X RJ-45 ports Interface (Port Uplink/PD support PoE power... - Page 12 Operating ~ 40 C (32 ~ 104 Temperature Operating 10% - 90%(non-condensing) Humidity Power Supply 48V/1.25A Power Adaptor (Optional)