Related Manuals for Pakedge Device & Software S8Mpdp
Summary of Contents for Pakedge Device & Software S8Mpdp
- Page 1 QUICK START GUIDE S8Mpdp Enterprise-Class, 8-Port PoE Powered Priority Switch S8Mpdp Quick Start Guide...
-
Page 2: Table Of Contents
Preparing to Install the Switch ........................... 6 Installation ................................ 6 Configuration ..............................8 Configuring the Switch Using the Web Interface (Windows 7) ................ 8 QoS Configuration ............................11 Resetting The IP Address From Terminal ...................... 13 Troubleshooting & Support ..........................14 S8Mpdp Quick Start Guide... -
Page 3: Introduction
The S8Mpdp is preconfigured for prioritization. It includes 8 10/100/1000 ports where port 1 can be used to power the switch using PoE. You can either use a PoE injector or another PoE switch to power the S8Mpdp. Additionally, it includes 1 Gigabit SFP interface and a console interface. The features of the standard ports are... - Page 4 1 SFP Port Implements 10/100/1000M Fiber connection using a GBIC Console Implements switch management using a console cable Reset Resets switch to factory defaults. Table 3: Description of the Rear Panel of the S8Mpdp from left to right S8Mpdp Quick Start Guide...
- Page 5 Devices connected to ports 6-7 will have normal priority Device(s) connected to port 8 will have low priority If additional ports/switches are needed they can be connected into the S8Mpdp so quality of service is not bypassed. S8Mpdp Quick Start Guide...
-
Page 6: Preparing To Install The Switch
OPTIONAL: If mounting the switch in a standard 19” AV rack, attach the rack mounting brackets, included with the S8Mpd, to the sides of the unit. The switch can also be mounted to the wall using the same included rack mounts. See images below. S8Mpdp Quick Start Guide... - Page 7 Physically mount the S8Mpdp switch near the power and network connections (i.e. backbone switch, firewall/router or behind a TV) 2. Connect the S8Mpdp to a power source 3. Connect your computer to any of the available ports on the S8Mpdp.
-
Page 8: Configuration
Configuration There are two ways to complete the initial configuration of the S8Mpdp switch: Using the standard IP address and a web browser Using a console cable and a terminal emulation program such as PuTTY or HyperTerminal. Configuring the Switch Using the Web Interface (Windows 7) 1. - Page 9 (Be sure the IP address and subnet mask are on the same subnet as the S8Mpdp). 4. Click OK to close the dialog then click OK to close the Local Area Connection Properties dialog.
- Page 10 8. In the web administration portal, you will be able to configure, update and reset the S8Mpd. Figure 5: S8Mpdp Web Interface PLEASE NOTE: Once you have logged in, you may use the web interface (Figure 5) to configure the switch and customize it for your environment.
-
Page 11: Qos Configuration
QoS Configuration The S8Mpdp is preconfigured with QoS out of the box but you can alter the QoS configuration to the needs of your network. To adjust the QoS settings you will need to log into the GUI using the steps mentioned earlier. - Page 12 The switch uses four classes of high, med, normal, and low for the port priorities. To set a port to a class you will run the command as follows: qos default port number class So for example if you wanted port 5 to be a low priority you would run the following command: qos default 5 low S8Mpdp Quick Start Guide...
-
Page 13: Resetting The Ip Address From Terminal
4. Once you see the terminal screen, enter pakedgep for the password. 5. Type: IP Setup 192.168.1.200 255.255.255.0 192.168.1.99 <ENTER> 6. Your switch should now be accessible from the network. Figure 5: Console Connection in Terminal Window S8Mpdp Quick Start Guide... -
Page 14: Troubleshooting & Support
Troubleshooting & Support If you are unable to get the S8Mpdp switch functional using this guide, you can refer to the full manual on our website or contact our Technical Support department for help. They are available Monday through Friday from 6:00 AM to 6:00PM PST.