Subscribe to Our Youtube Channel
Related Manuals for Intermec PB20
Summary of Contents for Intermec PB20
- Page 1 Quick Start Guide PB20 2-Inch Belt Printer Equipped with a Bluetooth Qualified Module by Socket Communications...
-
Page 2: Packing List
Part Number Replacement Li-Ion 900 mAhr Battery 320-082-021 Thermal paper 105’/roll, 50/case 816-034-022 Standard Paper Printer Cleaning Kit (2-inch printer) 320-081-014 Standard Paper Printer Cleaning Card (2-inch printer) 320-066-013 Linerless Paper (contact Supply Sales 1-800-255-6292) PB20 Printer Quick Start Guide... -
Page 3: Getting Started
Getting Started Here are the main components of the Intermec PB20 printer. Cover Latch Charge LED (red charging; green complete) Paper Advance Computer to Printer Jack Charger Jack Belt Clip PB20 Printer Quick Start Guide... -
Page 4: Charging The Lithium Ion Batteries
This printer has a built in low battery detector. When the print- er’s battery voltage is low, the printer beeps three times, indicat- ing a Low Battery Warning. This only happens if the printer is awake. PB20 Printer Quick Start Guide... -
Page 5: Paper Loading
Paper Loading Out of Paper The PB20 Printer sounds two quick beeps when it runs out of paper. If the printer is out of paper, the printer suspends opera- tion until paper is present and the lever is down. The printer continues to communicate with the mobile computer as long as it does not “time out.”... - Page 6 You will need about two inches of paper coming out of the mechanism. 8 Lower the cover while placing the extra paper though the tear bar. 9 Close Latch Cover and tear off extra paper. PB20 Printer Quick Start Guide...
-
Page 7: Printer Self-Test
“LOC” shows whether a font is Resident (R) or Downloaded (D). “CPI” shows characters per inch. “DESCRIPTION” describes the graphic. “NAMES” give the “Easy Print” name, the Line Printer name, and the hexadecimal equivalent of that name. PB20 Printer Quick Start Guide... -
Page 8: Battery Pack Removal
ESD static free mat before placing your printer on the mat and begin removing the bat- tery pack. Use only the battery pack designed for your PB20 Printer. Use only the Intermec 900 mAh Li-Ion battery p/n 320-082-021. Using any other battery may present a risk of fire or explosion. - Page 9 Set the printer assembly down to view the underside of printer mechanism and battery compartment. Battery pack compartment Printer assembly wire cluster Battery pack cable PB20 Printer Quick Start Guide...
- Page 10 Remove the four screws securing the battery cover. Avoid contact with the printer control board unless the board is grounded. Battery cover screws PB20 Printer Quick Start Guide...
- Page 11 S The wires must not be pinched or crimped when rein- serting the printer mechanism into the printer case. Reposition the battery pack assembly on the printer mechanism. Replace the four screws to secure the battery pack cover to the printer mechanism. PB20 Printer Quick Start Guide...
- Page 12 2 As you use the printer the power comes from the battery in the printer. When the printer battery runs down the printer will not operate until the battery is recharged. PB20 Printer using Wireless Printing Serial/Wireless Mode Your printer comes to you as a serial mode printer. To switch the mode to Wireless Printing it is necessary to toggle the mode via the self-test function of the printer.
- Page 13 On. Click Next, then select Finish. 7 A progress bar appears indicating Service Discovery is being performed. If the discovery is successful a screen with Successful discovery displays. Click Finish. The remote device icon appears in the PB20 Printer Quick Start Guide...
- Page 14 Note: Dropping your printer can cause a power in- terruption to your wireless printing operation. To ensure that your ”Wireless Printing” is still active, print a self-test. If the radio is Off, the self-test turns the radio On. PB20 Printer Quick Start Guide...
-
Page 15: Maintenance And Troubleshooting
Charge battery if necessary or replace. Note: If the battery is depleted, it may take 5-10 minutes of charging before the printer can print a self-test. 2 Make sure the paper is properly installed (with lever closed). PB20 Printer Quick Start Guide... - Page 16 Paper Options button. Adjust the Dark- ness setting to a higher percentage until the print is dark and crisp. Refer to the Intermec Portable Printers Technical Reference Manual (p/n: 978-018-001) Section 4 for more details.
-
Page 17: Specifications
Programming Problems Refer to the Intermec Portable Printers Technical Reference Manu- al (p/n: 978-018-001) Section 4 for more details OR call the Intermec Technical Support 1-800-755-5505 for assistance. Specifications Printer Specifications Item Spec Detail Dimension 4.39 x 5.65 x 2.4 in. -
Page 18: Global Services And Support
Global Services and Support Warranty Information To understand the warranty for your Intermec product, visit the Intermec web site at http://www.intermec.com and click Service & Support. The Intermec Global Sales & Service page appears. From the Service & Support menu, move your pointer over Support, and then click Warranty. -
Page 19: Telephone Support
Talk to sales administration, place an order, or check the status of your order. Outside the U.S.A. and Canada, contact your local Intermec representative. To search for your local representative, from the Intermec web site, click Contact. PB20 Printer Quick Start Guide... - Page 20 Corporate Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com e 2003 by Intermec Technologies Corporation. All rights reserved. PB20 Bluetooth 2-Inch Printer Quick Start Guide-April 2004 *962018024D* PN 962-018-024D PB20 Printer Quick Start Guide...
Need help?
Do you have a question about the PB20 and is the answer not in the manual?
Questions and answers