Lenovo NE1032 Quick Start Manual
Hide thumbs
Also See for NE1032:
- Product manual (26 pages) ,
- Quick start manual (22 pages) ,
- Installation manual (112 pages)
Related Manuals for Lenovo NE1032
Summary of Contents for Lenovo NE1032
- Page 1 Lenovo NE1032 Switch Quickstart Guide Document Version 1.0: 10/2018 1 © Scale Computing 2018...
-
Page 2: Table Of Contents
Table of Contents Introduction 3 Requirements 3 Connect to the Switch 4 Over the Network 4 Console 4 CLI Mode Basics 5 Set the Management IP 6 Management Configuration Example 6 Management VLAN Configuration Example 6 Update the Firmware 7 ... -
Page 3: Introduction
Introduction This guide provides general configuration examples. The configurations found here may not be applicable for all environments. Consult Lenovo’s official documentation for further information in regards to your environment's unique configuration. Requirements ● This guide was written for CNOS version 10.8.1.0. If you are on a lesser version, update to match 10.8.1.0 ... -
Page 4: Connect To The Switch
Connect to the Switch Over the Network By default, the management interface is set to request a DHCP address. If DHCP is available, check your leases on your DHCP server to determine the IP address of the switch. Using an SSH client, you may log in to the switch over the network. -
Page 5: Cli Mode Basics
CLI Mode Basics Configuration for the NE1032 is performed through a CLI interface. As a reference: > = unprivileged mode # = privileged mode (config)# = global configuration mode (config-if)# = interface configuration mode (config-vrf)# = virtual routing and forwarding configuration mode ... -
Page 6: Set The Management Ip
Set the Management IP The management network should be separated from any data networks and have physically independent hardware supporting it. The goal of the management network is to maintain remote access to network equipment should a configuration change interrupt the data networks. Optionally, you may use a VLAN interface instead. ... -
Page 7: Update The Firmware
Unzip the archive. Rename the extracted folder to n e1032 and place it in your local user home directory. Make sure your firewall will allow port 22, or turn it off temporarily. If you are using a linux machine, ensure sshd is running. # copy sftp sftp://10.205.105.202//home/cdraper/ne1032/NE1032-CNOS-10.8.1.0.imgs system- image all vrf management ... - Page 8 Boot image installation succeeded. OS image installation succeeded. Boot loader now contains Software Version 10.8.1.0 Standby image now contains Software Version 10.8.1.0 Switch is currently set to boot active image. Do you want to change that to the standby image? (y/n) [n] y ...
-
Page 9: General Configuration
General Configuration Set the Enable Mode Password (config)# enable password SOMEPASS Generate New SSH keys # conf t (config)# no feature ssh (config)# ssh key rsa length 4096 force (config)# ssh login-attempts 3 (config)# feature ssh ... -
Page 10: Set Dns
1-10 Verify Spanning Tree (config)# sh spanning-tree Ensure that the spanning tree protocol supports rapid convergence. By default the NE1032 uses r apid-pvst . VLAN0001 spanning-tree enabled protocol rapid-pvst ROOT ID priority 32769 address a48c.db96.7f00... -
Page 11: Logging
Logging Troubleshooting relies heavily on inspecting the switch logs. In this example, we are setting logging to debug level and storing them locally, allocating the maximum size possible for local storage of the logs. (config)# logging logfile switch_log 6 size 10485760 (config)#... -
Page 12: Port Configuration
Port Configuration By default, all ports are in access mode for VLAN 1. If you are not utilizing VLANs in your environment, you will not need to configure the VLAN settings for the switch ports further. We recommend isolating backplane ports for Scale Computing equipment to a VLAN other than 1 using access mode. ... -
Page 13: Link Layer Discovery Protocol
Link Layer Discovery Protocol LLDP is very useful for troubleshooting and network mapping. (config)# interface ethernet 1/1 (config-if)# lldp transmit (config-if)# lldp receive (config-if)# lldp trap-notification (config-if)# To view information about neighboring network devices: # show lldp neighbors [detail] #... -
Page 14: Feedback & Support
Feedback & Support Document Feedback Scale Computing welcomes your suggestions for improving our documentation. Please send your feedback to documentation@scalecomputing.com . Technical Support and Resources There are many technical support resources available for use. Access this document, and many others, at http://www.scalecomputing.com/support/login/...