AT&T CL84200 Quick Start Manual

Quick start guide
CL84100/CL84200/CL84250/CL84300/CL84350
This quick start guide provides you with basic instructions only.
For more detailed instructions, refer to your Abridged user's
manual provided in the package, or see the online Complete
user's manual at www.telephones.att.com/manuals.
Telephone base installation
•
Plug the large end of the AC power adapter into
•
Plug the small end of
a power outlet not controlled by a wall switch.
the AC power adapter
into the power jack
•
Plug the other end
on the bottom of the
of the telephone
telephone base.
line cord into a
telephone jack or
•
Plug one end of
a DSL filter.
the telephone
If you have DSL high-speed
line cord into the
Internet service, a DSL filter
telephone jack on
(not included) is required.
the bottom of the
•
Raise the antenna.
telephone base.
Charger installation
•
Plug the other
• end of the coiled
Plug the large end of
handset cord into
the AC power adapter
the jack at the
into a power outlet not
left side of the
controlled by a wall
telephone base.
switch.
•
Place the cords into
the channels.
Caution: Use only the power adapter provided with this product. To obtain a replacement, visit
www.telephones.att.com 1 (800) 222-3111
our website at or call
1 (866) 288-4268
Canada, dial .
Battery installation
Install the battery as shown below. Charge your handset(s) before initial use.
The battery is fully charged after 16 hours of continuous charging.
Step 1 Step 2
Plug the battery connector Align the cover flat
securely into the socket against the battery
compartment, then
inside the handset battery
slide it upwards until it
compartment, matching the
clicks into place.
color-coded label. Insert the
supplied battery with the
label THIS SIDE UP facing
up as indicated.
CHARGE light
Step 3
Charge a cordless handset by placing it face
forward in the charger. The CHARGE light on the
top of the handset is on during charging.
Use only the supplied rechargeable battery or replacement battery (model BT166342).
Quick reference guide - handset
CHARGE indicator
• On when the handset is
Handset
charging.
q CID/-VOLUME
• Press qCID to show caller
ID history when the handset
is not in use.
• Press to scroll down while
in menus.
• While entering names or
numbers, press to move the
cursor to the left.
• Press to decrease the
listening volume when on
a call, or to decrease the
message playback volume.
PHONE/FLASH
• Press to make or answer a
call.
• During a call, press to answer
an incoming call when you
receive a call waiting alert.
1
• While reviewing a caller ID
log entry, press repeatedly to
add or remove 1 in front of
the telephone number before
dialing or saving it in the
directory.
TONE
• Press to switch to tone
dialing temporarily during a
call if you have pulse dialing.
. In
/SPEA�ER SPEA�ER
• Press to switch between
the speakerphone and the
handset.
MUTE/DELETE
• During a call, press to mute the
microphone.
• While reviewing the caller ID history, the
directory or the redial memory, press to
delete an individual entry.
• While predialing, press to delete digits.
EQ
• During an outside call, intercom call,
Handset
message or announcement playback,
side view press to change the audio quality to
best suit your hearing.
Quick reference guide - telephone base
MENU/SELECT
FLASH
MENU/SELECT
Press to show the menu.
During a call, press to
• When the handset is not
While in the menu, press to
in use, press to show the answer an incoming call
menu. when you receive a call select an item or save an
waiting alert. entry or setting.
• While in the menu, press to
select an item or save an
p
CANCEL /DIR
entry or setting.
While using menus, press to Press when the phone is idle
cancel an operation, back up
to display the directory.
pDIR/VOLUME+
to the previous menu or exit
Press to scroll up while in
the menu display.
• Press pDIR to show
menus and lists.
directory entries when the
q
/CID
While entering or modifying
handset is not in use.
names, press to move the
Press when the phone
• Press to scroll up while in
cursor to the right.
menus. is idle to display the call
history. INTERCOM
• While entering names or
numbers, press to move the
Press to scroll down while
When the phone is idle, press
cursor to the right.
in menus and lists.
to initiate an intercom call.
• Press to increase the
While entering numbers or
listening volume when on
a call, or to increase the characters, press to move
message playback volume.
the cursor to the left.
Telephone base
OFF/CLEAR
• During a call, press to hang
up.
• While in a menu, press to
cancel an operation, back
up to the previous menu, or
exit the menu display.
• Press and hold while the
telephone is not in use
to erase the missed call
indicator.
# (pound key)
• Press repeatedly to display
other dialing options when
reviewing a caller ID log
entry.
INT
• Press to begin an intercom
conversation or to transfer
a call.
REDIAL/PAUSE
• Press repeatedly to view
the last 20 numbers dialed.
• While entering numbers, TONE
press and hold to insert a
If you have pulse dialing, press
dialing pause.
during a call to switch to tone
dialing temporarily.
MUTE
Press to turn off the microphone; press again
to resume your conversation.
SPEA�ER
Press to switch between speakerphone and
corded handset.
Initial settings
We recommend you program your telephone system before use.
IN USE indicator
The following are a few examples of common features to set before using the
telephone. Refer to the Handset and telephone base settings and Answering
On when the telephone is in
use, or when the answering
system settings in the Abridged user's manual or the online Complete user's
system is answering an
manual for detailed instructions on setting all telephone features.
incoming call.
On during the handset
Set date/time
registration process.
Set the date/time before using the answering system.
Flashes when another
telephone is in use on the Using a cordless handset or the telephone base:
same line.
1. MENU -> q or p -> Settings -> SELECT.
Flashes when there is an
2. q or p -> Set date/time -> SELECT.
incoming call or when the
3. q or p -> Date & time -> SELECT.
system is deregistering
handset(s).
4. Enter the month, day and year using the dialing keys -> SELECT.
5. Enter the hour and minute using the dialing keys.
LOCATOR
6. q or p to choose AM or PM -> SELECT.
When the phone is idle, press to
page all handsets.
Record your own announcement
Your outgoing announcement plays when calls are answered by the answering
system. You can use the preset announcement to answer calls, or replace it
with your own recorded announcement.
Using a cordless handset or the telephone base:
/ANSWER ON
1. MENU -> q or p -> Answering sys -> SELECT.
Press to turn the built-in answering system 2. SELECT to select Announcement.
on or off.
3. Press 7. After the tone, speak towards the handset or telephone base to
/PLAY/STOP record your announcement.
4. Press 5 to end recording.
Press to start or stop message playback.
Flashes when there are new messages or
Number of rings
memos in the answering system.
You can set the answering system to answer an incoming call after two,
X/DELETE
four, or six rings, or toll saver. If you choose toll saver, the answering system
Press to delete the message currently
playing. When in idle mode, press twice to answers a call after two rings if you have new messages, or after four rings
delete all old messages.
when there are no new messages.
/REPEAT
If you want the built-in answering system instead of the voicemail to answer a
Press to repeat the message; press twice
call, you should set the answering system to answer a call at least two rings
to play the previous message.
before the voicemail is set to answer. Contact your telephone service provider
/S�IP
for information on your voicemail settings.
Press to skip the message.
Using a cordless handset or the telephone base:
qp/VOLUME
MENU -> q or p -> Answering sys -> SELECT.
1.
During message playback, press to adjust
2. q or p -> Ans sys setup -> SELECT.
the listening volume.
3. q or p -> # of rings -> SELECT.
While in idle mode, press to adjust the
4. q or p -> Choose among 2, 4, 6 or Toll Saver -> SELECT.
base ringer volume.
REDIAL/PAUSE
Ringer volume
Press to access the last 20 numbers dialed.
You can set the ringer volume level to one of the six levels or turn the
While predialing or entering numbers into
ringer off.
your directory, press and hold to insert a
Using a cordless handset or the telephone base:
dialing pause.
1. MENU -> q or p -> Ringers -> SELECT.
2. SELECT to select Ringer volume.
3. q or p to choose the desired level -> SELECT.
Language
If you want to change the display language, or you have accidentally changed
the language and want to switch it back to English, follow the below steps.
Using a cordless handset or the telephone base:
1. MENU -> q 5 times -> SELECT twice.
2. q or p to choose the desired language, or choose English if you want to
change the display language to English -> SELECT.