AT&T CL84115 Quick Start Manual

Quick start guide
CL84115/CL84215/CL84265/CL84365
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user's
manual provided in the package, or see the online Complete
user's manual at www.telephones.att.com/manuals.
Telephone base installation
Plug the large end of the
Plug one end of the
telephone base power
telephone line cord into
a telephone jack or a adapter into a power
DSL filter. outlet not controlled by a
wall switch.
If you have DSL high-speed
Internet service, a DSL filter
Telephone line cord Route the cords through
(not included) is required.
the channels.
Plug the other end of the
telephone line cord into the Plug the small end of the
telephone jack on the back telephone base power
of the telephone base. adapter into the power
adapter jack on the back
of the telephone base.
Charger installation
Plug the power adapter Route the handset cord
into a power outlet not through its channel.
controlled by a wall switch.
One end of the
coiled telephone
line cord has already
been plugged into
Plug the other end of the coiled the handset. Make
handset cord into the jack on the
sure it is plugged in
back of the telephone base.
firmly.
Caution: Use only the power adapter provided with this product. To obtain a replacement, visit
www.telephones.att.com 1 (800) 222-3111
our website at or call
1 (866) 288-4268
Canada, dial .
Battery installation
Install the battery, as shown below. Charge your handset(s) before initial use.
The battery is fully charged after 10 hours of continuous charging.
Step 1 Step 2
Plug the battery connector securely into Align the cover flat against the
the socket inside the handset battery battery compartment, then slide it
compartment. Insert the supplied battery upwards until it clicks into place.
with the label THIS SIDE UP facing up,
as indicated.
CHARGE light
Step 3
Charge the handset
by placing it face
forward in the
handset charger. The
CHARGE light on the
top of the handset is
on during charging.
Use only the supplied rechargeable battery or replacement battery (model BT183342/BT283342).
Quick reference guide - cordless handset
CHARGE indicator
pDIR/VOLUME
On when the handset is
Press pDIR to show directory
charging in the charger.
entries when the handset is not
in use.
q CID/VOLUME
Press to scroll up while in menus.
Press qCID to show caller ID
While entering names or
log when the handset is not
numbers, press to move the
in use.
cursor to the right.
Press to scroll down while in
Press to increase the listening
menus.
volume when on a call, or to
increase the message playback
While entering names or
volume.
numbers, press to move the
cursor to the left.
MENU/SELECT
Press to decrease the listening
volume when on a call, or
When the handset is not in use,
to decrease the message
press to show the menu.
playback volume.
While in the menu, press to
REDIAL/PAUSE select an item or save an entry
or setting.
Press repeatedly to view the
last 10 numbers dialed.
While entering numbers,
press and hold to insert a During a call, press to hang up.
dialing pause.
While in a menu, press to cancel
an operation, back up to the
PHONE/FLASH previous menu, or exit the menu
display; or press and hold this
Press to make or answer a call. button to exit to idle mode.
During a call, press to answer an When the handset is ringing,
incoming call when you receive
press to mute the ringer
a call waiting alert.
temporarily.
During message playback, press Press and hold while the
to call back the caller if the
telephone is not in use to erase
caller's number is available.
the missed call indicator.
QUIET# (pound key)
1
Press repeatedly to display other
While reviewing a caller ID dialing options when reviewing a
log entry, press repeatedly to caller ID log entry.
. In
add or remove 1 in front of
Press and hold to enter the
the telephone number before
QUIET mode setting screen, or to
dialing or saving it.
deactivate QUIET mode.
Press and hold to set or dial
your voicemail number.
EQ
During an outside call, intercom
TONE /a>A
call, message or announcement
playback, press to change the
Press to switch to tone dialing
audio quality to best suit your
temporarily during a call if you
hearing.
have pulse service.
MUTE/DELETE
While entering names, press
to change the next letter to
During a call, press to mute the microphone.
upper or lower case.
When the handset is ringing, press to mute the ringer
temporarily.
/SPEAKER SPEAKER
While reviewing the caller ID log, the directory or the redial
memory, press to delete an individual entry.
Press to make or answer a call
using the speakerphone. While predialing, press to delete digits.
During message or announcement playback, press to delete
Press to switch between the
the playing message or the recorded announcement.
speakerphone and the handset.
Cordless
handset
side view
PUSH TO TALK
Press to initiate a one-to-one or
one-to-group broadcast.
Press and hold to broadcast to a group
of system devices.
Quick reference guide - telephone base
1 IN USE indicator
Press and hold to set or to On when the telephone is in use, or when the answering
dial your voicemail number.
system is answering an incoming call.
On when a handset is being registered.
Flashes when there is an incoming call or when all
handsets are being deregistered.
Flashes when another telephone is in use on the same line.
Large tilt display
OFF/CANCEL
/HANDSET LOCATOR
While the telephone is idle, press to page all handsets.
CANCEL
While in a menu, press to cancel an operation, back
up to the previous menu or exit the menu display; or
press and hold to go back to idle mode.
When the telephone base is ringing, press to mute the
ringer temporarily.
When the telephone base is not in use, press and hold
to erase the missed call indicator.
q
CID
Press to display the caller ID log when the telephone
is not in use.
Press to scroll down while in menus and lists.
While entering names or numbers, press to move the
cursor to the left.
X/DELETE
While reviewing the caller ID log, the directory or the
redial memory, press to delete an individual entry.
While predialing, press to delete digits.
During message or announcement playback, press to
delete the playing message or announcement.
Press twice to delete all old messages when the
telephone is not in use.
During playback, press to repeat the playing message.
During playback, press twice to play the previous
message.
Press to skip a message.
MUTE
Press to record memo or record your own
During a call, press to mute the
announcement.
microphone.
When the telephone is ringing, press
to mute the ringer temporarily.
Press to turn the built-in answering system on or off.
/SPEAKER
Press to make or answer a call using
Press to start or stop message playback.
the speakerphone.
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using the
telephone. Refer to the Handset and telephone base settings and Answering
system settings in the Abridged user's manual or the online Complete user's
manual for detailed instructions on setting all telephone features.
Set date/time
Set the date/time before using the answering system.
VOL p/VOL q
Using a cordless handset or the telephone base:
During message playback or call screening,
1. MENU -> q or p -> Set date/time -> SELECT.
press to adjust the listening volume.
2. Enter the month, day and year using the dialing keys -> SELECT.
While in idle mode, press to adjust the
3. Enter the hour and minute using the dialing keys.
base ringer volume.
4. q or p to choose AM or PM -> SELECT.
When on a call, press to adjust the
listening volume.
Basic answering system setup via voice guide
INT
Your can follow the voice guide to record your own announcement, set the
Press to initiate an intercom conversation or
number of rings, and set the message alert tone.
transfer a call.
PTT/FLASH Using the telephone base:
Press to initiate a one-to-one or one-to-
1. MENU -> q or p -> Answering sys -> SELECT.
group broadcast.
q or p -> Voice guide -> SELECT.
2.
Press and hold to broadcast to a group of
3. Set up your answering system by inputting the designated numbers,
system devices.
as instructed.
During a call, press to answer an incoming
call when you receive a call waiting alert.
Record your own announcement
MIC
Your outgoing announcement plays when calls are answered by the answering
Microphone.
system. You can use the preset announcement to answer calls, or replace it
with your own recorded announcement.
p
DIR
Using a cordless handset or the telephone base:
Press to display the directory when the
1. MENU -> q or p -> Answering sys -> SELECT.
telephone is not in use.
2. SELECT to select Announcement.
Press to scroll up while in menus and lists.
3. q or p -> Record annc -> SELECT.
While entering names or numbers, press
4. After the tone, speak towards the handset or telephone base to record your
to move the cursor to the right.
announcement. Press 5 to end recording.
MENU/SELECT
-OR-
When the telephone base is not in use,
press to show the menu.
Using the telephone base:
While in the menu, press to confirm or
1. /RECORD -> -> q or p -> Announcement -> SELECT.
save an entry or setting.
2. After the tone, speak towards the handset or telephone base to record your
REDIAL/PAUSE
announcement. Press 5 to end recording.
Press repeatedly to view the last 10
numbers dialed. Number of rings
While entering numbers, press and hold
You can set the answering system to answer an incoming call after two, three,
to insert a dialing pause.
four, five or six rings, or toll saver. If you choose toll saver, the answering
system answers a call after two rings when you have new messages, or after
four rings when there are no new messages. This enables you to check for
new messages and avoid paying unnecessary long distance charges if you are
calling from out of your local area.
If you want the built-in answering system instead of the voicemail to answer a
call, you should set the answering system to answer a call at least two rings
before the voicemail is set to answer. Contact your telephone service provider
for information on your voicemail settings.
Using a cordless handset or the telephone base:
/REPEAT
1. MENU -> q or p -> Answering sys -> SELECT.
2. q or p -> Ans sys setup -> SELECT.
3. q or p -> # of rings -> SELECT.
4. q or p -> Choose among 2, 3, 4, 5, 6 or Toll saver -> SELECT.
/SKIP
Ringer volume
/RECORD
You can set the ringer volume level to one of the six levels or turn the
ringer off.
Using a cordless handset or the telephone base:
/ANS ON/OFF
1. MENU -> q or p -> Ringers -> SELECT.
2. SELECT to select Ringer volume.
/PLAY/STOP
3. q or p to choose the desired level -> SELECT.