Autonics TZN4S Instruction Manual

DRW170714AA
Dual PID Control Temperature Controller
TZN SERIES
I N S T R U C T I O N M A N U A L
Thank you for choosing our Autonics product.
Please read the following safety considerations before use.
Safety Considerations
※Pleaseobserveallsafetyconsiderationsforsafeandproperproductoperationtoavoidhazards.
※Safety considerations are categorized as follows.
Warning Failure to follow these instructions may result in serious injury or death.
Caution Failure to follow these instructions may result in personal injury or product damage.
※The symbols used on the product and instruction manual represent the following
symbol represents caution due to special circumstances in which hazards may occur.
Warning
1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury
or substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles,
railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failuretofollowthisinstructionmayresultinfire,personalinjury,oreconomicloss.
2. Install on a device panel to use.
Failure to follow this instruction may result in electric shock.
3. Do not connect, repair, or inspect the unit while connected to a power source.
Failuretofollowthisinstructionmayresultinelectricshockorfire.
4. Check 'Connections' before wiring.
Failuretofollowthisinstructionmayresultinfire.
5. Do not disassemble or modify the unit.
Failuretofollowthisinstructionmayresultinelectricshockorfire.
Caution
2
1. When connecting the power input and relay output, use AWG 20(0.50mm ) cable or over and tighten
the terminal screw with a tightening torque of 1.0N . m.
When connecting the sensor input and communication cable without dedicated cable, use AWG
28~16 cable and tighten the terminal screw with a tightening torque of 1.0N . m.
Failuretofollowthisinstructionmayresultinfireormalfunctionduetocontactfailure.
2. Use the unit within the rated specifications.
Failuretofollowthisinstructionmayresultinfireorproductdamage.
3. Use dry cloth to clean the unit, and do not use water or organic solvent.
Failuretofollowthisinstructionmayresultinelectricshockorfire.
4. Do not use the unit in the place where flammable/explosive/corrosive gas, humidity, direct sunlight,
radiant heat, vibration, impact, or salinity may be present.
Failuretofollowthisinstructionmayresultinfireorexplosion.
5. Keep metal chip, dust, and wire residue from flowing into the unit.
Failuretofollowthisinstructionmayresultinfireorproductdamage.
Ordering Information
TZN 4 S 1 4 R
Control
R Relay output
output
S SSR drive output
C Current output
Powersupply
4 100-240VAC 50/60Hz
※1
1 Event 1
2 Event 1 + Event 2
Option output
R Event1+PVtransmission(DC4-20mA)
T Event 1 + RS485 communication
A Event1+Event2+PVtransmission(DC4-20mA)
B Event 1 + Event 2 + RS485 communication
S DIN W48×H48mm
M DIN W72×H72mm
Size
W DIN W96×H48mm
H DIN W48×H96mm
L DIN W96×H96mm
Digit
4 9999(4-digit)
Item
TZN Temperaturecontroller(PIDNewType)
※ T heunitcannotbeconfiguredwithanyrandomcombinationfromtheaboveorderinginformation.Please
refer to Specificationsforpossibleconfigurations.
※1: TZN4S only supports Event 1 option output.
※ The above specifications are subject to change and some model may be discontinued
without notice.
※ B e sure to follow cautions written in the instruction manual and the technical descriptions
(catalog, homepage).
Specifications
Series TZN4S TZN4M TZN4W TZN4H
Powersupply 100-240VAC 50/60Hz
Allowable voltage range 90 to 110% of rated power voltage
Max.5VA(100-
Powerconsumption 240VAC50/60Hz) Max.6VA(100-240VAC50/60Hz)
Display method 7-segmentLED(PV:red,SV:green)
PV(W×H) 7.8×11.0 mm 8.0×13.0 mm 7.8×11.0 mm
Character
8.0×10.0 mm
size
SV(W×H) 5.8×8.0 mm 5.0×9.0 mm 5.8×8.0 mm
RTD DPt100Ω,JPt100Ω,3-wire(allowedresistance:max.5Ωperline)
Input K(CA),J(IC),R(PR),E(CR),T(CC),S(PR),N(NN),W(TT)
TC
type (allowedresistance:max.100Ωperline)
Analog 1-5VDC ,0-10VDC ,DC4-20mA
Display accuracy F.S. ±0.3% or 3℃,greatervalue
Relay 250VAC 3A 1c
Control
SSR Max. 12VDC ±3V 30mA
output
Current DC4-20mA(loadresistancemax.600Ω)
EVENT1 250VAC 1A 1a
EVENT2 - 250VAC 1A 1a
Option
output
PVtransmission - DC4-20mA(loadresistancemax.600Ω)
Communication - RS485 communication
Control method ON/OFF,P,PI,PD,PIDF,PIDScontrol
Alarm output hysteresis 1 to 100℃(0.1to100.0℃)variable
Proportionalband(P) 0.0 to 100.0%
Integraltime(I) 0to3,600sec
Derivativetime(D) 0to3,600sec
Controlperiod(T) 1 to 120 sec
Sampling period 0.5 sec
LBA setting 1 to 999 sec
Ramp setting RampUp,RampDown:1to99mineach
Dielectric strength 2,000VAC50/60Hzfor1min(betweeninputandpowerterminals)
Mechanical 0.75mmamplitudeatfrequency10to55Hz(for1min)ineachX,Y,Zdirectionfor2hours
Vibration
Electrical 0.5mmamplitudeatfrequency10to55Hz(for1min)ineachX,Y,Zdirectionfor10min
Control output Mechanical:min.10,000,000operations,
Electrical:min.100,000operations(250VAC3Aresistanceload)
Relay
life cycle
Mechanical:min.20,000,000operations,
Option output
Electrical:min.500,000operations(250VAC1Aresistanceload)
Insulation resistance Over 100MΩ(at500VDCmegger)
Noise immunity Squareshapednoisebynoisesimulator(pulsewidth1㎲)±2kVR-phase,S-phase
Memory retention Approx.10years(non-volatilesemiconductormemorytype)
Ambient temp. -10 to 50℃,storage:-20to60℃
Environ
ment
Ambient humi. 35to85%RH,storage:35to85%RH
Approval
Approx. 226g Approx. 355g Approx. 351g
※1
Weight
(approx.164g) (approx.246g) (approx.232g)
※1: The weight includes packaging. The weight in parentheses is for unit only.
※Environment resistance is rated at no freezing or condensation.
Input Type and Range
Input type Decimal point Display Inputrange(℃) Inputrange(℉)
K(CA) 1 KCaH -100 to 1300
K(CA) 0.1 KCaL -100.0 to 999.9
J(IC) 1 0 to 800
JIcH
J(IC) 0.1 0.0 to 800.0
JIcL
R(PR) 1 0 to 1700
R PR
E(CR) 1 ECrH 0 to 800
Thermo
couple
E(CR) 0.1 ECrL 0.0 to 800.0
T(CC) 1 -200 to 400
TCcH
T(CC) 0.1 -199.9 to 400.0
TCcL
S(PR) 1 0 to 1700
S PR
N(NN) 1 NN 0 to 1300
W(TT) 1 U TT 0 to 2300
JPt100Ω 1 JPtH 0 to 500
JPt100Ω 0.1 -199.9 to 199.9 -199.9 to 391.8
JPtL
RTD
DPt100Ω 1 0 to 500
DPtH
DPt100Ω 0.1 DPtL -199.9 to 199.9 -199.9 to 391.8
0 - 10VDC A--1
-1999 to 9999
Voltage
Analog 1 - 5VDC (displayrangewillvarydependingonthe
A--2
decimalpoint.)
Current DC4 - 20mA
A--3
Configuring Input Type
Pleaseconfiguretheinternalswitchesbeforesupplyingpower.Aftersupplyingpower,configuretheinputtype
[IN-T] in parameter group 2 according to the input type.
Input type S/W 1 S/W 2
Thermocouple
RTD 1 1 mA V
Voltage
(0-10VDC,
1-5VDC)
2 2 mA V
Analog
Current
(DC4-20mA)
2 2 mA V
●Detachingthecase
Pressthefrontcasethenpullthecasetodetachthecasefromthebody.
Configuretheinternalswitchesasinputtype.
Dimensions
●TZN4S
TZN4L
48
9.8×14.2 mm
8.0×10.0 mm
10 79.5 10.5
100
●TZN4H
48
TEMPERATURE CONTROLLER
PV °C
SV
SV2 AT OUT EV1 EV2
MD AT
13 90 10
Panel cut-out dimensions
A
C
Approx. 474g (unit:mm)
(approx.303g)
Size
A B C D
Series
TZN4S Min. 55 Min. 62 45.5 +0.5 45.5 +0.5
0 0
TZN4M Min. 91 Min. 91 68 +0.7 68
+0.7
0
0
TZN4W Min. 112 Min. 50 92 45.5
+0.8 +0.6
0 0
-148 to 2372 TZN4H Min. 50 Min. 102 45 +0.6 92 +0.8
0 0
Not supported
TZN4L Min. 98 Min. 106 91 +0.5 91 +0.5
0 0
32 to 1472
Not supported
Connections
32 to 3092
32 to 1472 ●TZN4S
Not supported
-328 to 752
EV1 OUT
SOURCE
SV2 IN
Not supported 250VAC 100-240VAC
Max.5VDC
1A 1a
50/60Hz 5VA
250㎂
32 to 3092
B'
-
32 to 2372
- H
TC MAIN OUT
+ B +
32 to 4172
250VAC 3A 1c
C Resistive load
SENSOR
32 to 932
A L
RTD
32 to 932
●TZN4W
MAIN OUT
250VAC 3A 1c
PVOUT
SOURCE
Resistive load
DC4-20mA
100-240VAC
H L
+ - 50/60Hz 6VA
RS485 RS485
C
- + (A+) (B-)
B' B A
RTD
EV1 OUT EV2 OUT SV2 IN - +
250VAC 250VAC Max.5VDC
SENSOR
TC
1A 1a 1A 1a 250㎂
●TZN4L
EV1 OUT
250VAC 1A 1a
EV2 OUT
250VAC 1A 1a -
H
MAIN OUT
+
SV2 IN
250VAC 3A 1c
C
Max.5VDC Resistive load
250㎂ L
RS485(A+) +
B'
PVOUT
-
TC DC4-20mA
B
+
RS485(B-) -
SENSOR
A
SOURCE
RTD
100-240VAC
50/60Hz 6VA
●TZN4M ●TZN4W
72 96
10 73
83
●TZN4L
96
13 90
Bracket
TZN4S Series TZN4M,TZN4W,TZN4H,TZN4LSeries
4.2
41
12.2 47.8
48
61
●TZN4M
MAIN OUT EV1 OUT
250VAC 1A 1a
SSR Current
EV2 OUT
- - 250VAC 1A 1a
3 3
V mA
B'
2 2
-
+ +
TC
B SV2 IN
+
12VDC ±3V DC4-20mA
Max.5VDC
30mA Max. Load600ΩMax.
250㎂
SENSOR A
RTD
●TZN4H
EV1 OUT
250VAC 1A 1a
EV2 OUT
250VAC 1A 1a
MAIN OUT
SV2 IN
Max.5VDC
SSR Current
250㎂
- -
RS485(A+)
B'
15 15
-
mA
V TC
14 14 B
+
+ +
SENSOR
RS485(B-) -
A
12VDC ±3V DC4-20mA
30mA Max. Load600ΩMax. RTD
MAIN OUT
SSR Current
- -
15 15
V mA
14 14
※
+ +
12VDC ±3V DC4-20mA
30mA Max. Load600ΩMax.
(unit:mm)
13 90 10
10
30
73
-
H MAIN OUT
MAIN OUT
+
SSR Current
250VAC 3A 1c
C
Resistive load
L - -
7 7
V mA
RS485(A+) +
6 6
+ +
PVOUT
DC4-20mA
12VDC ±3V DC4-20mA
RS485(B-) - 30mA Max. Load600ΩMax.
+
SOURCE
-
100-240VAC 50/60Hz 6VA
-
H
MAIN OUT
+
MAIN OUT
250VAC 3A 1c
C
Resistive load
L SSR Current
- -
+
15 15
PVOUT
mA
V
DC4-20mA 14 14
+ +
12VDC ±3V DC4-20mA
30mA Max. Load600ΩMax.
SOURCE
100-240VAC
50/60Hz 6VA
Useteminalsofsizespecifiedbelow.
a b
a b
<Round> <Forked>
a Min. 3.5mm Min. 3.5mm
b Max. 7.2mm Max. 7.2mm