Controls; Time Defrosting; Cooking In One Stage; Memory Function - Anvil MWA1100 Installation, Operation And Care Manual

CONTROLS

TIME DEFROSTING

When DEFROST is selected, the automatic cycle divides the defrosting time into periods of
alternating defrost and stand times by cycling on and off.
1. Touch DEFROST pad.
DEFROST
2. Touch number pads for the
desired defrosting time.
3. Touch START pad.
When you touch START pad, the DEFROST indicator lights to show the oven is in the DEFROST mode.
The display counts down the time to show you how much defrosting time is left in the DEFROST mode.
The oven beeps during the defrosting cycle to signal that the food needs to be turned or rearranged. When
the defrosting time ends, you will hear 3 beeps.

COOKING IN ONE STAGE

1. Touch POWER pad.
POWER
x3
(Select desired power level.)
2. Touch the number pads for the
cooking time.
3. Touch START pad.
When you touch START pad, the MICROWAVE indicator lights to show the oven is cooking.
The display counts down the time to show how much cooking time is left. When the cooking time ends,
you will hear 3 beeps.
NOTE: Using lower power levels increases the cooking time which is recommended for foods such
as cheese, milk and slow cooking of meats.
The DEFROST indicator lights and " : 0" is
displayed.
The display will show the numbers you
pressed in the order you touched.
NOTE: Your oven can be programmed for
60 minutes.(60:00)
The MICROWAVE and % indicators light.
The display will show what you touched.
This example shows power level 60.
The display will show the numbers you
pressed in the order you touched.
NOTE: Your oven can be programmed
for 60 minutes. (60:00)
but, in case of full power(100%),
maximum time is 20 minutes.
(20:00)
12
6

MEMORY FUNCTION

This microwave oven has 20 programmable pads (1~20).
1. Touch PROGRAM pad.
PROGRAM
2. Touch the NUMBER pad to be
programmed.
(ex. number pad 1)
3. Touch POWER pad.
(Select desired power level.)
4. Touch the NUMBER pads for
cooking time.
5. Touch START pad to save
cooking time and power level.
6. Touch STOP/CLEAR pad.
NOTE 1: If you want cooking in two or three stage, repeat step 3~5 once or twice, and display will
show "STAGE-2" or "STAGE-3".
After touching START pad to save cooking time and power level in 3-stage, you can see
" - END - " on the display.
NOTE 2: Programs 1~10 are already programmed from the factory as shown below.
After programming is finished, just touch the NUMBER pad of the memory number you want to select.
To select the memory number 11 to 20, touch the number pad twice rapidly. Then the oven will
automatically start heating according to the pre-programmed cooking time and power level.
* Preprogrammed Cooking Times and Power Level
Pad Cooking Time
1 10 sec.
2 20 sec.
3 30 sec.
4 45 sec.
5 1 min.
6 1 min.30 sec.
7 2 min.
8 3 min.
9 4 min.
10 5 min.
The display will show "PROGRAM".
The display will show "PROG-01".
To program pads 11 to 20, touch number
pad twice rapidly.
(ex. to program pad 11, touch number pad
1 twice rapidly.)
The MICROWAVE and % indicators light.
The display will show what you touched.
The display will show "STAGE-2" and long
beep sounds.
When you touch STOP/CLEAR pad,
MEMORY function ends.
Power Level
100 %
100 %
100 %
100 %
100 %
100 %
100 %
100 %
100 %
100 %
14
7