Advertisement
Front Door Content: 13711.15 (2dr/4dr)
1. Soft Upper Door frame with Cover
2. Adjustment Collar
3. Allen Wrench
4. Velcro Strip (38" )
Rear Door Content: 13712.15 (4dr)
1. Soft Upper Door Frame with Cover
2. Adjustment Collar
3. Allen Wrench
4. Velcro Strip (30")
This product is intended to provide added "o -road" convenience and utility to your vehicle.
This product is not intended to provide occupant containment or protection in the event of an accident or roll-
over. Further, "on road" use may involve increased risk of serious injury in the event of side-impact accidents. To
reduce risk from these types of injuries: Always wear seat belt and shoulder harness for all vehicle occupants.
Keep arms and body inside vehicle. Drive safely, read and understand all manufacturers warnings and product
instructions before installation.
NOTICE: The Rugged Ridge soft upper doors when used in conjunction with the Rugged Ridge Half Doors are
designed to provide the best possible protection from the elements; however, due to the nature and intended
use of this product, extreme conditions such as driving rains, high wind gusts, automated car washes, etc. may
cause leaking to occur.
1. Lower 1/2 doors will need to be cleaned using isoproply (rubbing) alcohol. Clean the 2" along the top edge
where Velcro is to be installed. Installation should be performed between (65F-110F).
2. Apply Velcro to outer edge of front lower 1/2 door. With 2" of backing tape removed position Velcro 1/8"
below top edge of door (Pic. 2). Working forward from rear of door slowly apply Velcro to door maintaining
1/8" spacing from top edge. For front doors cut a "V" shaped notch 3/4 through Velcro at each bend. This will
allow the Velcro to follow the door line without bunching (Pic. 3). Press Velcro rmly in place to ensure good
adhesion.
Pic. 1
JK Upper 1/2 Door Installation Instructions
Quantity:
2
4
1
2
Quantity:
2
4
1
2
Front 1/2 Door Installation
Upper Soft Door Kit (Front) 2dr - 4dr JK : 13711.15
Upper Soft Door Kit (Rear) 4dr JK:
Pic. 2
Page 1 of 6
13712.15
Pic. 3
Advertisement
Table of Contents
Related Manuals for Rugged Ridge 13711.15
Summary of Contents for Rugged Ridge 13711.15
- Page 1 Keep arms and body inside vehicle. Drive safely, read and understand all manufacturers warnings and product instructions before installation. NOTICE: The Rugged Ridge soft upper doors when used in conjunction with the Rugged Ridge Half Doors are designed to provide the best possible protection from the elements; however, due to the nature and intended use of this product, extreme conditions such as driving rains, high wind gusts, automated car washes, etc.
- Page 2 3. For front doors drape Velcro over the top of the mirror mounting base (Pic. 4). Make a small cut where the mirror base begins and where it ends. Pull the Velcro back and cut out the shape of the mirror mounting base (Pic.
- Page 3 7. With door closed a 1/8” gap should be visible at top corners (Pic. 10). If there is more or less than a 1/8” gap at top corners further adjustment will be needed. 8. To adjust corners up place palm of hand on top corner of upper door. Push up slightly to raise frame (Pic.
- Page 4 Door Seal Adjustment Procedures (Front Doors) 13. From inside of vehicle inspect upper door frames for visible light entering around the door seal. If light is visible frames will need to be bent slightly inward (towards vehicle) to eliminate gaps. 14.
- Page 5 19. Open half door and grab the excess weather-stripping closest to the Windshield frame. Place the weather stripping behind the post of the soft upper frame (Pic. 25). Adjust as needed to ll gap between windshield frame and upper door . 20.
- Page 6 Features and Functions of Soft Upper Doors Rugged Ridge upper door windows can be set in 3 new distinct positions. By unzipping the window and sliding plastic dowels through the elastic straps the door can be con gured as shown.
Need help?
Do you have a question about the 13711.15 and is the answer not in the manual?
Questions and answers