Advertisement
3
Installation
Note:
Please read the instructions carefully before installing the k-Kadex.
The k-Kadex has one wire attached to it. For a neat installation, you need to conceal this wire
properly.
2
1
1
Remove the back piece of the k-Kadex from the main piece.
Secure the back piece of the k-Kadex onto or inside a wall using the 4 screws provided but
2
make sure that you have some space for the wire to go through the center hole. Plug the
main piece of the k-Kadex securely in place.
Verification •
User ID & Password
4
Make sure that the k-Kadex is in its standby
1
mode, where the Red LED light is lit on and
the user ID and/or password(s) have been
enrolled into a master terminal before you
proceed with verification.
Insert a user ID, for example 1234. Ignore the
2
prefix zeros if the user ID has them. Press OK
to confirm the user ID You will hear a beep.
This is an indication that the User ID has
been sent to the master terminal.
Insert a password, for example 387034, and
3
press OK to confirm. If the password is
correct, you will hear a "beep" after you
press the OK button.
Verification result
a. Successful Verification:
Green
blinks accompanied with a long beeping
sound.
b. Failed Verification: Red LED blinks
accompanied with two short beeping
sound.
Note:
There are 2
small hooks inside
the
back
piece.
Make
sure
this
portion is facing up.
Master terminal indication during the
verification process at the k-Kadex:
Pwd Affirm
• Input a
username
User ID
00004
ESC
OK
Pwd Affirm
• Input a
password
User ID
00004
Input Pwd*___
Pwd Affirm
• During
successful
User ID
00004
verification
Verified, TQ
LED
• During
Pwd Affirm
dailed
verification
Error Pwd.
5
Verification •
Card
Wave a card at the card induction area to scan
the card. The k-Kadex captures the card informa-
tion and transmits it to the master terminal for
verification. Make sure that the k-Kadex is in its
standby mode, where the LED light is showing
red before you start using the terminal.
Make sure that you have enrolled the
1
user/card into the master terminal.
Wave the card at the card induction area. The
2
LED light will turn green and it will submit the
card information to the master terminal for
verification.
3
Verification result
a. Successful Verification: Green LED blinks
accompanied with a long beeping sound.
b. Failed Verification: Red LED blinks accom-
panied with two short beeping sound.
SPECIFICATIONS
k-Kadex
MODEL
Acrylonitrile Butadiene Styrene (ABS)
SURFACE FINISHING
RFID antenna
TYPE OF SCANNER
MICROPROCESSOR
Managed by master
MEMORY
ALGORITHM
PRODUCT DIMENSION (L X W X H), mm
75 x 20 x 115
STORAGE
• Cards
Storage in master
• Transaction
ENROLLMENT & VERIFICATION
• Methods
Card & password
Managed by master
• Card per user ID
40 ~ 80 (RFID), 30 ~ 50 (Mifare)
• Reading distance, mm
Managed by master
• Verification time (sec)
CARD TECHNOLOGY
Yes
• RFID: 64-bit, 125kHz
Made to order
• MIFARE: MFIS50/S70, 13.56MHz
COMMUNICATIONS
Wiegand 26-bit output
• Method
OPERATING ENVIRONMENT
• Temperature (°C)
-10 ~ 70
• Humidity (%)
20 ~ 80
DC 12V 1A
• Power input
ACCESS CONTROL
• EM lock driving output
Managed by master
• Alarm output
• Antipassback
Master
terminal
indication
during
verification process at the k-Kadex:
• During
successful
verification
Verify
CARD: 0003837885
USER ID: 00001
VERIFIED
• During failed
Verify PIN Card
verification
No enroll
A Firm Access
with FingerTec
k-Kadex
Card
Password
Advertisement
