Technical Specifications - jablotron JA-80V Manual

7.2. The communicator's LEDs
Green LED:
regular flashing – communication in progress (ARC, SMS or
remote access)
off – data is waiting to be sent to an ARC
lit permanently – no waiting data to be sent to an ARC
Red LED:
off – communication to the ARC is OK
lit permanently – impossible to send data to any ARC
Yellow LED:
regular flashing – Ethernet connected, DHCP is not working
off – Ethernet is not connected
lit permanently – Ethernet connected and communication with
the network is OK
7.3. After entering service mode the communicator:
• finishes reporting to ARCs (if any is needed)
• unfinished SMS and call reports are cancelled
• unsent ARC reports are only erased if ARC tel. numbers / IP
addresses or the ARC communication format or the installation ID are
changed
• alarm restoration reports or fault restoration reports are sent to the
ARC even in service mode
• changes to communicator settings do not take effect until service
mode has been exited
7.4. Configuring the communicator in maintenance mode
If configuring the communicator in maintenance mode is enabled (via
control panel programming), then the above described programming
sequences can be used to set:
• tel. numbers M1 to M7
• the events reported by SMS and phone calls
7.5. Remote access by Internet
The system can be accessed remotely via
allows complete programming by installers and also operating the
system by end users. To access the system remotely it is necessary
to:
• Have the communicator connected to an Ethernet network which
allows access to www.GSMLink.cz
• Register the communicator via the GSMLink web page by:
o displaying www.GSMLink.cz
o setting your login details (name and password)
o entering the communicator
communicator label)
o entering your system access code (user or service – this gives
you access to the user menu or the installer menu accordingly)
o after entering the above parameters it should be possible to
establish a connection with the system.
If your communicator is using a dynamic IP address when
communicating with the GSMLink server, then it could be that you
will have to wait for a connection (if your IP address has been
changed). GSMLink will indicate how long it will take to get
connection with the system. To shorten the waiting time it is
possible to initialise the communication remotely by dialling from a
telephone which has been programmed for this function (see
5.10.1).
• for further access sessions you only need to enter your login details
(these can be memorized by your web browser)
• several people can register for internet access to the system (both
installers and users)
• A service technician needs only one set of login details to access
various installations. After the first system has been registered, the
installer can add (or remove) other installations to(or from) his/her
GSMLink account.
• there is a demo version of remote access on
• using www.GSMLink.cz is free of charge
7.6. A complete list of CID reports to ARCs
A report to an ARC consists of: installation ID, event code, subsystem
number and the number of the source (device or code). In IP CID and
SMS CID, in addition to this, a time stamp is also sent as follows.
List of the CID reports
The JA-80V LAN/PSTN line communicator
www.GSMLink.cz
and selecting New registration
registration code (see
www.GSMLink.cz
CID code
1130 / 3130
1134 / 3134
1110 / 3110
1120 / 3120
1461 / 3461
1140 / 3140
1137 / 3137
1144 / 3144
1406
1401 / 3401
3402
3408
1354 / 3354
1300 / 3300
1330 / 3330
1301 / 3301
1302 / 3302
1384 / 3384
1306 / 3306
1661 / 3661
1662 / 3662
1355
1350 / 3350
1602
1138
1351
1393
1551 / 3551
List of source numbers
which
Source Source
number
701 Control panel
731 Communicator
741 Wired keypad
001 - 050 Devices 01 - 50
500 Master code
599 Service code
501 - 550 Codes 01 - 50
Subsystem: 01 in all reports
the
In a split system, for setting and unsetting: 02 = A, 03 = B
For partial setting: 02 = A, 03 = AB

8. Technical specifications

Power
Stand-by consumption
Max. consumption (during communication)
Complies with
ATS 4 if the ARC comm. repeating period is zero (sequence 06a0)
ATS 5 if ID CID protocol is used and the repeating period is set to zero
(sequence 06a0)
Operating environment ( –10 to 40°C)
Safety
EMC
Radio transmissions
CLIP protocol (caller ID + SMS)
Jablotron Ltd. hereby declares that the JA-80V is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
Jablotron Ltd. hereby declares that the product complies with part 15
of the FCC rules. Operation is subject to the following two
conditions: 1. This device may not cause harmful interference, and 2.
This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could
void the user's authority to operate the equipment.
The original of the conformity assessment can be found at www.jablotron.com, -
Technical Support section
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer
after use.
- 10 -
Event
Intruder alarm – instant / restored
Intruder alarm – delayed / restored
Fire alarm / restored
Panic alarm / restored
Number of incorrect code-entries exceeded
alarm / restored
Alarm triggered during control panel power-up /
restored
Tamper alarm / no tampering
Device tamper alarm / no tampering
Alarm cancelled by user
Unsetting / setting
Partial setting
Codeless complete setting
External communication fault / restored
Fault (except device) / all faults restored
Device fault / all faults restored
Mains dropout longer than 30 minutes /
restored
Battery fault (except devices) / all battery faults
restored
Device battery fault / all battery faults restored
Switching to Service Mode / Leaving Service
mode
PGX ON/OFF
PGY ON/OFF
Radio communication jamming present
Internal communication fault / restored
Communication test
Unconfirmed alarm
Communication fault to ARC1
Annual check request
Communicator blocked / restored
12V DC (from the control panel)
EN 50131-1/2006, EN 50136-1-1, 2-1 as:
ETSI EN 301419-1 and EN 301511
ETSI EN 300 089 V3.1.1(2000-12)
ec
1 / 9
2 / 9
3 / 9
4 / 9
5 / 9
6 / 9
7 / 8
7 / 8
10
12 / 11
13
14
15 / 16
17 / 18
17 / 18
19, 20 / 21
22 / 23
22 / 23
24 / 25
26
27
28
29 / 30
31
32
to ARC2 if
backups
17
31 only in
IP CID
about 35 mA
1 A
class II
EN 60950
EN 55022, EN 5030-4
MKA51202