Table of Contents
Advertisement
Function
Selection of events to report by
phone call
SMS/phone call communication
checking period
SMS text editing*
Enable reporting to phones
Phone number for instant remote
access
Remote access
Forwarding of incoming SMSes
Reaction to incoming calls
Initialisation of GSMLink
communication
Tel. number to initialise GSMLink
communication
Tx SMS center tel. number
Rx SMS center tel. number
Testing reporting to an ARC
Test calls to a phone number
Programming by SMS
Triggering LAN re-log-in
Communicator reset
Automatic DHCP
Communicator IP address
Network mask
Network gateway address
DNS IP address
ARC main tel. number/IP address
ARC backup tel. number/IP
address
Installation (alarm system) ID for
ARC use
Selecting the ARC protocol
Selection of events to report to
ARCs
Defining the delay before data is
resent to an ARC
The JA-80V LAN / PSTN line communicator
Sequence
x=1 report, x=0 no report
83 M ec x
hhmm = hours and minutes in range from
00:00 to 24:00
84 hhmm
(The time to wait after the last SMS/phone call
report before performing an SMS/phone
communication check)
Texts can be edited by Comlink software or by SMS instruction:
code TXT n,text,n,text... or by
x=0 disabled
x=1 enabled (all programmed by 82.. & 83..)
x=2 enabled without reporting
setting/unsetting by users 41 to 50 (codes,
80 x
cards & key-fobs) and master code
setting/unsetting
x=3 only if ARC1 is not responding
x=4 only if ARC1 is not responding
902 xx..x ∗ ∗ ∗ ∗ 0
xx..x = tel. number (max.20 digits)
x=0 disabled
903 x
x=1 enabled (by phone and Internet)
x=0 no, x=1 yes = if the incoming text is not an
926 x
SMS instruction it will be forwarded to the first
programmed number in memories M1 to M8
x=0: no reaction
904 x
x=1 to 8: answers after 1 to 8 rings
x=9: answers after the 2
913
initialises communication to GSMLink
914 xx..x ∗ ∗ ∗ ∗ 0
xx..x = tel. number (max.20 digits)
942 xx..x ∗ ∗ ∗ ∗ 0
xx..x = tel. number (max.20 digits)
943 xx..x ∗ ∗ ∗ ∗ 0
xx..x = tel. number (max.20 digits)
961 a
a=1=ARC1, a=2=ARC2
962 M
M = tel. number memory from 1 to 8
System can be programmed remotely via SMS instruction code PRG seq, seq,... where seq is programming
sequence set also from the keypad (e.g. 8080 PRG ∗ ∗ ∗ ∗ 08080,201,# set the 10s exit delay)
935
The communicator will log out of the LAN network and then re-log-in (DHCP update)
98080
Resets to the factory default settings and erases all phone numbers
x=0 disabled
930 x
x=1 enabled
xx..x = IP address 12 digits (if automatic
931 xx..x
DHCP disabled)
xx..x = network mask 12 digits (if automatic
932 xx..x
DHCP disabled)
xx..x = IP address 12 digits (if automatic
933 xx..x
DHCP disabled)
xx..x = IP address 12 digits (if automatic
934 xx..x
DHCP disabled)
a=1=ARC1, a=2=ARC2, xx..x = IP address &
01 a xx..x ∗ ∗ ∗ ∗ 0
port for ARC1 – e.g. 01 2 ∗8 192 168 001 123
08080 ∗0 (∗8= signifies an IP address, it must
have 12 digits followed by a 5 digit port
number).
02 a xx..x ∗ ∗ ∗ ∗ 0
Tel. number for ARC2 (max.20 digits)
Entering 01p∗0 or 02p∗0 will erase the
number/address
a=1=ARC1, a=2=ARC2, zz..z = ID number
03 a zz..z ∗ ∗ ∗ ∗ 0
max. 8 digits 0 to 9 and ∗1=A to ∗6=F
(hexadecimal number)
a=1 ARC1, a=2 ARC2
04 a x
x=0 CID, x=1 IP CID
a=1 ARC1, a=2 ARC2
05 a ec x
ec event code (see 5.26)
x=1 report, x=0 no report
a=1 ARC1, a=2 ARC2
06 a x
x=0 to 9 min. (0=immediately, without delay)
Options
www.GSMLink.cz
via Internet
nd
call
- 3 -
Factory default
by SMS
M7 alarms by call
M8 technical faults by SMS (to installer)
24:00
see 5.4
x=1
enabled
erased
enabled
yes
answers after 5 rings (25s)
erased
erased
erased
enabled
192.168.001.211
255.255.255.0
192.168.001.001
192.168.001.001
erased
0000
CID
all events are reported
1 minute
MKA51202
Advertisement
Table of Contents
