jablotron JA-80V Manual page 6

Lan / pstn line communicator

Hide thumbs

Table Of Contents

Table of Contents

Factory-default SMS report and instruction texts

Factory text

Report from your

alarm:

Device

• The communicator always automatically puts numbers from 01: to 50: in front of Device or Code names.

• Texts 0 to 532 are used to create SMS event reports

• Texts 601 and 611 are SMS instructions (to control the system remotely by SMS)

5.6.

Phone number for instant remote access

A telephone number programmed with this sequence allows instant

remote access no matter what reaction to incoming calls is

programmed. If this number calls, the control panel will answer the call

after the first ring (the telephone line must provide CLIP protocol caller

ID for this feature).

902 xx...x ∗ ∗ ∗ ∗ 0

where

Note:

• if remote access is disabled (see 5.7), then using this phone number

for remote access is also disabled.

Factory default setting: erased

5.7.

Remote access

Remote access (by phone or Internet) can be enabled or disabled:

9030

disabled

9031

enabled

Factory default setting: enabled

5.8.

Forwarding of incoming SMS messages

This feature enables the automatic forwarding of incoming SMS

messages which contain no valid instructions to the system:

The JA-80V LAN/PSTN line communicator

Factory text

Device

201

Control panel

202

Service code

203

Annual inspection request

204

Communicator

205

Keypad

206

ARC code

300

Master code

301

Code

302

Code

303

Code

304

Code

305

Code

306

Code

307

Code

308

Code

309

Code

310

Code

311

Code

312

Code

313

Code

314

Code

315

Code

316

Code

317

Code

318

Code

319

Code

320

Code

321

Code

322

Code

323

Code

324

Code

325

Code

326

Code

327

Code

328

Code

329

Code

330

Code

331

Code

xx...x = phone number

Factory text

332

Code

333

Code

334

Code

335

Code

336

Code

337

Code

338

Code

339

Code

340

Code

341

Code

342

Code

343

Code

344

Code

345

Code

346

Code

347

Code

348

Code

349

Code

350

Code

400

System status

401

Set

402

Unset

403

Exit delay

404

Entrance delay

405

Alarm

406

Service mode

407

Maintenance mode

408

Partial setting

409

Discharged battery

410

Tamper alarm

411

Alarm memory

412

Fault

413

Power fault

414

Unknown status

415

Time:

416

Last event:

417

Credit unknown

418

Credit:

419

not used

420

Error while processing

command

421

Output turned on

422

Output turned off

501

Instant alarm

502

Delayed alarm

9260

messages are not forwarded (will not be used)

9261

messages are forwarded to the first programmed tel.

number in memories M1 to M8 (e.g. if numbers are only

programmed in M5 and M6, then messages will be

forwarded to M5). The tel. number from which the SMS

was received will be shown at the beginning of the

forwarded text.

Factory default setting: messages are forwarded

5.9.

Reaction to incoming calls

The communicator's reaction to incoming phone calls can be set by:

904 x

where

x = 0

x = 1 to 8

x = 9

Factory default setting: 9045 – answers after 25 sec. (about 5 rings)

- 6 -

Factory text

503

Fire

504

Panic alarm

505

Invalid code-entries exceeded

506

Alarm when power turned on

507

Tamper alarm

508

End of tamper alarm

509

End of alarm indication

510

Alarm cancelled by user

511

Setting

512

Unsetting

513

Partial setting

514

Codeless setting

515

External communication fault

516

External comm. restored

517

Fault

518

Fault no longer present

519

Mains dropout over 30 minutes

520

Mains dropout

521

Mains recovery

522

Discharged battery

523

Battery OK

524

Switching to Service Mode

525

Leaving Service Mode

526

PGX

527

PGY

528

Radio jamming present

529

Internal communication fault

530

Internal comm. restored

531

Communication test

532

Unconfirmed alarm

601

SET

602

UNSET

603

STATUS

604

MEMORY

605

PGX ON

606

PGX OFF

607

PGY ON

608

PGY OFF

609

AUX ON

610

AUX OFF

611

CREDIT

Numbers 01 to 50 for devices and codes are

automatically generated by the communicator

so it is unnecessary to enter them in the text

incoming calls are ignored

the communicator will answer after x multiplied

by 5 seconds of ringing (e.g. x=4=20sec.)

answers after a second call - first there must be

at least one ring, then a pause (10 to 45sec.) and

then just after the first ring of the second call, the

call will be answered

MKA51202

Table of Contents

jablotron JA-80V Manual page 6

Related Manuals for jablotron JA-80V

Related Products for jablotron JA-80V

Table of Contents