Table of Contents
Advertisement
This product must not be used by people (including children) with limited physical, sensorial, or
mental capacity or with inadequate experience or knowledge that are not supervised by a person
that is responsible for their safety or until they have been adequately trained. Children must be
supervised to ensure that they do not play with the product.
Do not clean the product while it is working and do not immerse it in water.
Warning! To use this unit as a portable product, first assemble the pedestal and fix it to the
product. Do not stand the product on the floor without its pedestal.
Do not coil the power cable around or on the product while it is working.
Do not use the product in rooms filled with explosive gases or vapours generated by solvents and
paints or that are inflammable.
If the cable gets damaged and has to be changed, do not do this yourself – take the equipment to
an authorised repair centre because the work must be done by specialist personnel to avoid any
risk of damage.
Do not use this equipment near showers, baths, or basins.
The product must be positioned in such a way that the power supply socket can always be
reached.
Important warning
If you have purchased a new product or if you have left your product without function for a long period,
when switching it on you may smell an odour.
This is due to the deposit of dust or impurities on the surface of the heating element. The smell is not
dangerous for health and it will disappear in a few minutes
3. Safe positioning
Only use the equipment in a horizontal position.
If used as a portable unit, always respect the minimum distances from any inflammable object
indicated in figure 2.
For wall mounting respect the minimum distances from the ceiling, floor, and side walls shown in
figure 3.
In bathrooms never install or use the equipment within zones 0 or 1 shown in figure 4.
The regulating knobs must never be accessible to people in a bath or shower.
The product must be free to take air in and expel it.
For portable use:
• Assemble the pedestal by screwing the rod (figure 1/D) to the base (figure 1/C) with the 2
countersunk screws supplied (fig 5).
• Insert the pedestal rod in the relevant rectangular slot that can be seen in the lower grille on the
product (figure 6).
•
Fix the pedestal to the product using the 4 screws supplied at the points indicated in figure 7.
This product has double electrical insulation and does not require an earth connection.
4. Wall mounting
The product can be wall mounted only if the pedestal is not fitted and respecting the distances
shown in figure 3.
Screw the product to the lower support bracket as shown in figure 8 using the screws supplied.
Fix the wall bracket by making 2 holes in the wall 150 mm apart, using a 6 mm drill bit. Insert the 2
wall anchors and fix the wall bracket using the 2 screws supplied as shown in figure 9.
Hook the product to the wall bracket first pushing it towards the wall and then making it click in
downwards (figure 10).
Use a pencil to mark the point at which to drill the hole for fixing the lower support, remove the
product, drill the hole in the wall using a 6 mm drill bit, and insert the wall anchor supplied (fig 11).
Hook the product to the plastic bracket again and fix the lower bracket using the relevant screws.
IMPORTANT FOR FRANCE:
If the product is to be wall mounted the electrical connection to the power supply must be done by
cutting off the plug supplied and using a suitable terminal as per the diagram shown below:
Phase = brown
L
Net
N
Neutral = blue
Product cable
In wet spaces like bathrooms or kitchens, the connection terminal must be installed at least 25 cm
above the floor. The electrical connection to the power supply must also be fitted with a two-pole
switch with a minimum gap between the contacts that allows complete disconnection according to
excess voltage III category conditions.
5. Cable winder
When the product is not in use the cable can be coiled as shown in figure 12.
Remember that when using the product the cable must be completely uncoiled.
6. Using the equipment
6.1 Model with thermostat only (figure 14A)
Turn the thermostat knob clockwise until you hear a "click". The product starts working at 1000 W.
The thermostat maintains the ambient temperature required by switching the equipment on and off
automatically. The more the thermostat knob is turned clockwise the higher the temperature
ensured. The maximum thermostat position corresponds to about 35° C, while the minimum (*) is
about 5° C.
When the product is working, slight undulations may occur on the surface of the heating
element inside the product.
This is completely normal and does not affect correct
functioning of the equipment or its reliability over time.
The producer does not accept any responsibility for damage caused by freezing, due to inadequate
insulation of the space or the equipment's heating capacity not being adequate for the size of the
space to be heated.
6.2 Using the thermostat
In a room in which the temperature exceeds 35° C it is normal that, even when turned to maximum,
the product does not switch on.
On the contrary, in a room in which the temperature is too low (below 5° C) it is normal that, even
when turned to minimum, the thermostat will keep the equipment switched on all the time.
To make the best thermostat setting, we recommend the following:
- Put the thermostat on maximum and allow the equipment to run until a comfortable temperature is
reached.
- Then turn the thermostat knob anticlockwise until you hear a "click", and the equipment switches
off.
- Then turn the thermostat knob clockwise again (only a little).
- In this position the thermostat will maintain the ambient temperature you have chosen.
When the product is working and heating the space, the relevant signal LED switched on.
6.3 Model with power and thermostat selector (figure 14B)
This model has 2 knobs, one for adjusting the operating power and one for the thermostat.
The power regulator can be used to select 3 different operating modes for the product:
O
=
OFF
I
=
750 W OPERATION
I I
=
1500 W OPERATION
Turn the thermostat knob clockwise until you hear a "click". The product starts working at the
power selected.
The thermostat maintains the ambient temperature required by switching the equipment on and off
automatically. The more the thermostat knob is turned clockwise to a position with a higher
number, the higher the temperature ensured. The maximum thermostat position corresponds to
about 35° C, while the minimum (*) is about 5° C.
WARNING! When the switch knob is at the maximum position (pos. II) do not turn it further
clockwise.
WARNING! When the thermostat knob is at the maximum position (pos. MAX) do not turn it
further clockwise.
Advertisement
Table of Contents
