Advertisement
2
1
WIRING EXAMPLES /
To connect all three outputs (sensor alarm, tamper and trouble/anti-
mask) to one zone input: All alarm, tamper and trouble/anti-mask
events are "alarms" when the system is armed or "fault" when disarmed.
FR) To connect all three outputs (sensor alarm, tamper and
trouble/anti-mask) to one zone input: All alarm, tamper and
trouble/anti-mask events are "alarms" when the system is armed or "fault"
when disarmed.
ES) To connect all three outputs (sensor alarm, tamper and
trouble/anti-mask) to one zone input: All alarm, tamper and
trouble/anti-mask events are "alarms" when the system is armed or "fault"
when disarmed.
PG) To connect all three outputs (sensor alarm, tamper and
trouble/anti-mask) to one zone input: All alarm, tamper and
trouble/anti-mask events are "alarms" when the system is armed or "fault"
when disarmed.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor. Keep 12" (30cm) in front
of the sensor clear.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor. Keep 12" (30cm) in front
of the sensor clear.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor. Keep 12" (30cm) in front
of the sensor clear.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor. Keep 12" (30cm) in front
of the sensor clear.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
LED
0 VDC - V
supply
1.8 mA max
2
WIRING EXAMPLES / WIRING EXAMPLES / WIRING EXAMPLES
Trouble
Tamper
30 mA
30 mA
25 VDC
25 VDC
LED TBL
TBL
T
T
9 8
7
6
5
Control Panel
LED TBL
9 8
Control Panel
Trouble
LED TBL
9 8
EOL
KOhm
* Off-Board, External EOLR (Not supplied),
best if installed inside the sensor housing.
- 2 -
Alarm
Power
30 mA
18 mA
25 VDC
9 - 15 VDC
-
+
C
NC
V
V
4
3
2 1
Zone
Zone
#
COM
TBL
T
T
C
7
6
5
4
(On-Board, Internal EOLR)
Anti-mask
EOL
Enabled
ON
ON
EOL
KOhm
1
2
2.2 5.6
Zone
Zone
COM
JUMPER
TBL
T
T
C
7
6
5
4
(On-Board, Internal EOLR)
Anti-mask
EOL
Enabled
ON
ON
1
2
2.2 5.6
EOL
ON
EOL
KOhm
1
2
2.2 5.6
Ground
+12V
-
+
NC
V
V
3
2 1
Alarm
Ground +12V
Zone
*
-
+
NC
V
V
3
2 1
W1
Cut
Advertisement
