Honeywell DC515 Series Operation Manual
Portable and plug-in wireless doorbell
Hide thumbs
Also See for DC515 Series:
- Getting started (2 pages) ,
- Quick start manual (2 pages) ,
- Manual (2 pages)
Advertisement
Installation and Operation Guide
Portable and Plug-In Wireless Doorbell
Preparation
Content will vary according to your kit
Doorbell
Push
Push Button Mounting
Button
Bracket
and Adhesive Pad
The push button supplied with this kit is pre-programmed to operate with the doorbell.
If it is not, see "Connect a Push Button" on page 7. Push button model may vary
from the one shown above.
Mounting Bracket
Wall
Round Head
Anchors
Screws
CR2032 Battery
Flat Head
Screws
DC515XX
English
Spanish
German
Portuguese
French
Italian
Dutch
To install you will need
Phillips Screwdriver
Standard Screwdriver
Advertisement
Table of Contents
Related Manuals for Honeywell DC515 Series
Summary of Contents for Honeywell DC515 Series
- Page 1 Installation and Operation Guide Portable and Plug-In Wireless Doorbell DC515XX English Spanish German Portuguese French Italian Dutch Preparation Content will vary according to your kit To install you will need Phillips Screwdriver Mounting Bracket Standard Screwdriver Wall Round Head Doorbell Anchors Screws CR2032 Battery...
-
Page 2: Setup And Operation
Overview Just follow these simple steps: 1. Install the push button battery. Depending on the model, plug in the doorbell or install the batteries in it. 2. Set up the doorbell and your preferences. 3. Install the push button. Doorbell for indoor use only. Do not expose to liquid, vapour or rain. Power-up 1. -
Page 3: Adjust The Volume
Change the Tune Press the Music button to change the doorbell tune. Every time you press the Music button, the tune will change. Stop pressing the Music button when you hear the tune you want. If you have multiple push buttons paired with the chime, you can select the melody for the last push button that was triggered. -
Page 4: Set The Mute
Set the Mute You can also mute the doorbell for specific amounts of time. Press the Mute button. Mute button shows Doorbell is mute Mute button shows Doorbell is mute 1 time doorbell is mute 4 times 9 hours 2 times 3 hours 5 times 12 hours... - Page 5 Wall Mount Installation (Portable Models Only) Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear. Install Doorbell If you are not mounting the doorbell to the wall, place the doorbell where you want it.
- Page 6 Accessories You can connect up to 4 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors. If you try to connect more accessories than the maximum number, the doorbell will sound two beeps. Connect a Motion Sensor 1.
- Page 7 Connect a Push Button Follow these steps to change the ring and halo light colour for an existing doorbell, too. 1. Press and hold the Setting button on the doorbell for three seconds. The halo light will circle. 2. Press the push button. 3.
-
Page 8: Maintenance
Maintenance Your doorbell and push button require no maintenance except to periodically change the battery. If using the correct battery, its life should be approximately: • Up to 2 years for the push button; replace with CR2032 lithium battery Low Battery Notification When the push button batteries are low, two beep sounds are heard after the normal tune. -
Page 9: Specifications
Specifications Doorbell Push Button Operating Temperature -5ºC to 40ºC -20ºC to 50ºC Honeywell Home ActivLink™ 868 MHz 868 MHz Range (open field) 150 m 150 m Sound Level (typical) 84 dB 3 x LR6(AA) 1.5V - battery Battery Type CR2032... - Page 10 ©2019 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International Inc. 32343180-001 Rev.A...