JUKI TL-2200QVP Instruction Manual
  1. Manuals
  2. Brands
  3. JUKI Manuals
  4. Sewing Machine
  5. TL-2200QVP Mini
  6. Instruction manual

JUKI TL-2200QVP Instruction Manual

Lockstitch machine with a long arm and a thread trimmer
Hide thumbs Also See for TL-2200QVP:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual , Service Manual & Parts List
Lockstitch machine with a long arm and a thread trimmer
TL-2200QVP
INSTRUCTION MANUAL
NOTE:
Congratulations on your purchase of a JUKI sewing machine.
Please be sure to read this Instruction Manual before operating the sewing machine
to ensure safe operation. Please be sure to keep the Instruction Manual so that you
can read it whenever necessary.
EN
ES
FR
IT
NL
DE
CS
PL
RU
JA

Advertisement

Table of Contents
loading

Related Manuals for JUKI TL-2200QVP

Summary of Contents for JUKI TL-2200QVP

  • Page 1 INSTRUCTION MANUAL NOTE: Congratulations on your purchase of a JUKI sewing machine. Please be sure to read this Instruction Manual before operating the sewing machine to ensure safe operation. Please be sure to keep the Instruction Manual so that you...

  • Page 2: Safety Regulations

    “IMPORTANT SAFETY INSTRUCTIONS” When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this sewing machine. “DANGER ____ To reduce the risk of electric shock:” 1. The appliance should never be left unattended when plugged in. 2.
  • Page 3 Congratulations on your purchase of a JUKI sewing machine. Please be sure to read safety precautions in “To use the sewing machine safely” in the Instruction Manual before use to fully understand the functions and operating procedures of the sewing machine so as to use the sewing machine for a long time.
  • Page 4 WARNING For the combination of the material and the thread and needle, in particular, refer to the explanation table in “Replacement of the needle”. If the needle or thread does not match the material used such as in the case that an extra heavy-weight material (e.g., denim) is sewn with a thin needle (#11 or higher), the needle can break resulting in an unexpected personal injury.

  • Page 5: How To Carry The Sewing Machine

    How to carry the sewing machine How to take out the sewing machine ■ CAUTION If you pull up the sewing machine by holding presser regulating screw section , the sewing machine can break. In addition, be aware that the presser regulating screw can break if a physical impact is given to it.

  • Page 6: Grounding Instructions

    GROUNDING INSTRUCTIONS This product must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.

  • Page 7: Table Of Contents

    CONTENTS Safety regulations ..................1-3 How to carry the sewing machine..............4 GROUNDING INSTRUCTIONS ..............5 Specifications ....................7 Accessories ....................8 Setup and operation ................9-11 Principal Parts .................... 12 Name and Function of each component..........13-17 Winding the bobbin ................18-21 Threading the machine (needle thread) ............. 22 Adjusting the thread tension ...............

  • Page 8: Specifications

    Specifications Description Specification Max. 2,200 sti/min Sewing speed 35mm Needle bar stroke 5.5mm Lift of presser foot GB 134R Needle New Defrix Oil No.1 Lubricating oil 22.2W x 46.0H x 73.0L (cm) Dimensions of sewing machine 26 kg Weight of sewing machine AC100V-AC240V/1.2A-0.8A, 50/60Hz Rated power supply / Power consumption –...

  • Page 9: Accessories

    Accessories 1. Power cord 2. Exclusive screwdriver 3. Screwdriver (small) 4. Cleaning brush 5. Bobbins (4pcs.) 6. Oiler 7. Needles (GB 134R #18) 8. Spool cap 9. Thread stand components (spool holder, thread stand thread guide, bobbin winder spool pin, bobbin winder seat, anti-vibration cone (2 pcs.), setscrew large, setscrews small (2 pcs.)) 10.

  • Page 10: Setup And Operation

    Setup and operation Basic Operating Procedures ■ 1) Insert the electric power cord plug into the corresponding inlet. Turn ON the power switch. This is described in the Instruction Manual. 2) Set the machine settings from the LCD screen. You can set the maximum sewing speed and the automatic thread trimming at the end of sewing.
  • Page 11 • Precise Stitch Mode The sewing machine won’t sew, even if you press the "start button" on the right handlebar. When you move the sewing machine by the handles, the machine will automatically sew a constant stitch length according to the distance moved.
  • Page 12 <2. Sit-down type> 1 Setting the Maximum Sewing Speed You can set the maximum sewing speed in 5% increments. 2 Auto Thread Trimming Function The sewing machine will trim the threads automatically when it stops. 3 Sewing and Manual Thread Trimming When you press part A of the foot controller (pedal), the sewing machine will start sewing.

  • Page 13: Principal Parts

    Principal Parts 1. Thread trimmer retaining plate 2. Bobbin winder guide 3. Presser foot pressure regulator 4. Thread tension dial 5. Lamp (built-in type) 6. Hand pulley 7. Support rod 8. Spool pin 9. Anti vibration cone 10. Bobbin presser 11.

  • Page 14: Name And Function Of Each Component

    Name and Function of each component Power cord ■ Insert the electric power cord plug into the corresponding inlet. CAUTION Turn OFF the power switch before insertion/removal of any cords and any plugs. Perform these following steps before you are not using your sewing machine.
  • Page 15 Installing the thread stand ■ CAUTION Turn OFF the power switch. Always must be disconnected plug from socket-outlet. 1. Insert bobbin winder spool pin 2 into spool holder 1. Fix the former with setscrew 3. 2. Set bobbin winder seat 4 and two anti-vibration cones 5 on spool holder 1.
  • Page 16 Panel cord binding procedure ■ CAUTION Turn OFF the power switch. Always must be disconnected plug from socket-outlet. Remove two setscrews from the presser regulator cover. Remove the presser regulator cover. Place the panel cord as illustrated in the figure. It is necessary to place the panel cord at a position where the cord does not come in contact with the mechanical parts.
  • Page 17 Installing the eye protection cover ■ CAUTION Turn OFF the power switch. Always must be disconnected plug from socket-outlet. DANGER Be sure to install the eye protection cover since the cover protects eyes from being injured by a fragment of a broken needle. 1.
  • Page 18 Adjusting the presser foot ■ stroke It is possible to adjust the presser foot stroke. Remove presser regulator cover. Loosen nut . Shift block upward to increase the stroke, or downward to decrease it. To increase the stroke more, change the position of setscrew of the link arm to the lower position (stroke: 3...

  • Page 19: Winding The Bobbin

    Winding the bobbin Positioning latches Bobbin winder guide Bobbin presser Bobbin thread winding shaft Thread trimmer retaining plate Installing the thread guide. CAUTION Turn OFF the power switch. Raise the support rod fully, turning slightly until the positioning latches engage. Set the large spool over the anti vibration cone.
  • Page 20 CAUTION Turn OFF the power switch. Take out the bobbin case. ■ Bring up the needle. Open the hook cover. Take out the bobbin case. Take out the bobbin from the bobbin case. ■ Snap in the latch to let the bobbin come out of the bobbin case. Thread the bobbin winder guide.

  • Page 21: Winding The Bobbin

    Upon completion of winding the bobbin. ■ Return the bobbin presser to its home position. Take out the bobbin. Trim the thread with the thread cutting knife. Loading the bobbin into the bobbin case. ■ Snap in the bobbin case latch, and put the bobbin into the bobbin case so that the bobbin runs clockwise.
  • Page 22 Adjusting the bobbin winder guide Good Thread unevenly wound around the bobbin would badly affect the bobbin thread tension. Loosen the screw of the bobbin winder guide to make adjustment. Thicker toward downside Move up Loosens Thicker toward upside Move down Tightens –...

  • Page 23: Threading The Machine (Needle Thread)

    Threading the machine CAUTION Turn OFF the power switch before threading or passing thread. * Bring the thread take-up to the upper end of its stroke. Then, pass the thread through it. Thread take-up Pass the thread through Pass the thread through ■...

  • Page 24: Adjusting The Thread Tension

    * Adjust the needle thread tension in accordance with the bobbin thread adjusting screw Increase tension. * The bobbin case for the TL-2200QVP is an exclusive JUKI part. Please consult the JUKI dealers when you purchase it. Decrease · Proper thread tension...

  • Page 25: Tabulated Relationship Between Material, Thread And Needle

    Tension controller No. 1 ■ When tension nut No. 1 is turned to the right A, the remaining length of thread after thread trimming is shortened. When it is turned to the left B, the remaining length of thread is lengthened. * Be sure to carry out back tacking by several stitches at the beginning of sewing.

  • Page 26: Attaching The Needle

    Attaching the needle Needle clamp screw CAUTION Turn OFF the power switch. Tightens Attaching the needle 1. Turn OFF the power switch. 2. Lower the presser foot. 3. Move the needle bar up to the highest position of Needle with its stroke.

  • Page 27: Maintenance And Lubrication

    Maintenance and lubrication Always must be disconnected plug from socket-outlet before cleaning or CAUTION lubricat ing the sewing machine. Cleaning the hook ● Turn OFF the power switch. Remove the needle. ● Loosen the screws to remove the throat plate. ●...

  • Page 28: Troubles And Corrective Measures

    Troubles and Corrective Measures If sewing difficulties occur, make sure the instructions are correctly followed. If a problem still exists, the reminders below help to solve it. Troubles Case Corrective measures Page 1. The needle is bent or the needle point ·...

Table of Contents