In an effort to reduce the possibility of injury to personnel working Training shall include instruction in operation under normal conditions around HYTROL conveying equipment, safety labels are placed at and emergency situations. various points on the equipment to alert them of potential hazards.
Conveyors angle (AJUSTE A LA ITEM ITEM ELEVACIÓN DESEADA) of incline will determine where the knee HYTROL CONVEYOR CO. INC. HYTROL CONVEYOR CO. INC. brace mounting brackets are to be placed JONESBORO, AR JONESBORO, AR "MATCH-MARK" NUMBERS when required.
• Connecting the V-Belts Model ACC FIGURE 5A “MATCH-MARK” NUMBERS The double groove sheave, located at one end of each conveyor section, is (etIQUetas de seCUenCIa de armadO) used to connect the driving V-Belts of the conveyor. The groove in which each belt is placed is predetermined at the factory.
SHEAVE SHEAVE (POLEA TENSORA) (POLEA MOTRIZ) • Belt Alignment • Electrical Equipment NOTES FOR 90 DEGREE: 190-LRC 90° CONTROLS 1. IT IS CRITICAL TO ALIGN BOTH IDLER SHEAVES WITH THE DRIVE SHEAVES SO THE BELT RUNS IN THE MIDDLE OF THE DRIVE SHEAVE 1.
• Racked Sections FIGURE 6B “Racked” conveyor sections SIDE CHANNELS will cause package to travel (Canal lateral) toward side of conveyor. ROLLERS NOT SQUARE WITH SIDE CHANNELS (rOdIllOs desCUadradOs COn Canales laterales) SIDE CHANNEL FIGURE 6C CROSSBRACING (LONG ROD) (Canal lateral) (tIrante tensOr [VarIlla larga]) "...
NOTE: Special length V-belts are used on the “ACC” & “LRSS” convey- lubricate more frequently. It may be best, under these conditions, to develop a ors. It is recommended that replacements be obtained from HYTROL. custom lubrication schedule for your specific application. A custom lubrication The Models “LRC”...
• Belt Replacement mOdELS “LRC” & “LRS” FIGURE 9B The models “LRC” & “LRS” have a take-up bracket mOdEL “ACC” located near the center on the underside of Take-up brackets with sheaves are located at both ends of the conveyor. To adjust the belt tension, locate conveyor section to adjust belt tension.
3) Low voltage to motor. 3) Have electrician check and correct as necessary. 4) Low lubricant level in reducer. 4) Relubricate per manufacturer’s recommendations. for HYTROL 5) One or more V-belts too tight. reducer, refer to separate manual. 5) Re-position take-up sheaves further from double groove sheave.
• Slave Connection Parts Drawing & Parts List Dibujo y Lista de Partes de Conexión Esclava 3 29/32 9 1/8 13 7/16 3 1/32 (esclavado externo) (Ver pág. 10) External Slave drive (See Pg. 10) (ensamble de la tangente 6-1/4) Ref.
• Model 190-ACC Parts Drawing Dibujo de Partes del Modelo 190-ACC (Vea la página 23 See Page 23 for para Opresores Sheave Retainers de polea) 15 16 21 22 24 23 24 12 13 30 31 33 VIEW B--B (Vista b--b)
• Model 190-ACC Parts List Lista de Partes del Modelo 190-ACC 1-1/2 1-1/2 Ref. No. Part No. description Ref. No. Part No. description — motor - C-face 042.914 Shoulder Bolt - Suspension Angle — 030.7134 1/2 HP - 230/460 VAC - 3 Ph. - 60Hz. - TEfC 042.550...
• Model 190-LRC 90 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRC de 90° 15 16 See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) END VIEW (Vista de Extremo) Ref.
• Model 190-LRC 60 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRC de 60° See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) END VIEW (Vista de Extremo) Ref. No. Part No.
• Model 190-LRC 45 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRC de 45° 15 16 See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) END VIEW (Vista de extremo) Ref.
• Model 190-LRC 30 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRC de 30° 40 39 15 16 See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) End View (Vista de extremo) Ref.
• Model 190-LRS 45 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRS de 45° 15 16 49 47 See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) End View (Vista de extremo) Ref.
• Model 190-LRS 30 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRS de 30° 50 51 45 46 47 See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) End View (Vista de extremo) Ref.
• Model 190-LRSS 45 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRSS de 45° See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) End View (Vista de extremo) Ref. No. Part No.
• Model 190-LRSS 30 ° Parts Drawing and List Dibujo y Lista de Partes del Modelo 190-LRSS de 30° See Page 23 for Sheave Retainers (Vea la página 23 para Opresores de polea) End View (Vista de extremo) Ref. No. Part No.
• Sub-Assemblies and Parts List Sub-Ensambles y Lista de Partes Ref. Part No. description 1-1/2 1-1/2 Conveyor Section (Specify model) — mS Type Pivot Plate - 1-1/2 in. flange — B-00913 3-11/16 in. High — B-02112 1-9/16 in. High — floor Support frame —...
• Sub-Assemblies and Parts List Sub-Ensambles y Lista de Partes B-06856 B-06855 B-10376 Part No. description Ref No. Part No. description 024.12431 V-Idler Sheave, 2.50 in. Od x 024.1211 Sheave V-Idler, 3.8125 in. Od x 5/8 in. Bore 3/8 in. Bore B-05324 Angle Bracket (Sheave) Ref.
Conexión de esclava ..11 localización o posición. dibujo y lista de modelo 190-aCC....12,13 La presencia alejada del público o empleado constituirá una medida de dibujo y lista de modelo 190-lrC de 90°...
HYTROL. Por favor, revise el equipo e identifique todas las 6. Instale los controles eléctricos y conecte el motor. etiquetas de seguridad. Asegúrese de que el personal conozca y obedezca estas advertencias.
• Montaje del Transportador FIGURE 26A DRIVE SECTION (seCCIón mOtrIz) INTERMEDIATE SECTION OR TAIL SECTION CENTER SUPPORT (seCCIón IntermedIa O (sOpOrte Central) seCCIOn de retOrnO) “MATCH-MARK” MATCH MARKS NUMBERS (etIQUetas de seCUen- END GUARD (etIQUetas de CIa de ar madO) (gUarda del eXtremO) seCUenCIa de armadO)
IDLER • Alineación de Banda DRIVE 190-lrC 60°, 45°, and 30° SHEAVE SHEAVE 1. alinear las dos poleas tensoras con las poleas motriz es crítico para (POLEA TENSORA) (POLEA 190-lrC 90° prevenir el desgaste de la banda que debe correr en medio de la polea MOTRIZ) 1.
del transportador. si es más efectivo y de acuerdo a las circunstancias se en el control del transportador concerniente y no debe depender de la puede utilizar una luz intermitente o una advertencia visual similar, en lugar parada de cualquier otro equipo. los dispositivos de parada de emergencia del dispositivo sonoro.
NOTA: Longitudes especiales de bandas-V son usadas en los transportadores “ACC” & “LRSS” . Se recomienda obtener el repuesto en HYTROL. más frecuencia. lo apropiado sería que bajo estas condiciones se establezca Los Modelos “LRC”...
• Reemplazo de la Banda MODELOS “LRC” y “LRS” FIGURE 30B los modelos “lrC” y “lrs” tienen un MODELO “ACC” soporte tensor ubicado en la parte inferior los soportes con poleas están ubicados en ambos extremos de la sección del transportador cerca del centro. del transportador para ajustar la tensión de la banda.
4) Vuelva a lubricar de acuerdo a las recomendaciones del fabricante. para el 5) Una o más bandas-V están demasiado tensas. reductor HYtrOl, refiérase al manual adjunto. 5) reubique las poleas tensoras más distantes de las poleas de doble ranura.
Page 32
General Check: All loose bolts, etc., tightened (revision general: tornillos sueltos, etc.) ( 8 7 0 ) 9 3 5 . 3 7 0 0 2020 HYTROL STREET W W W . H Y T R O L . C O M JONESBORO, ARKANSAS 72401 ( 8 7 0 ) 9 3 1 .
Need help?
Do you have a question about the 190-ACC and is the answer not in the manual?
Questions and answers