Table of Contents
Advertisement
3.0 Safety warnings
1.
Read and understand the entire owner's
manual
before
attempting
operation.
2.
Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury. Replace warning labels if they
become obscured or removed.
3.
This turret mill is designed and intended for use
by properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a turret mill do not use until
proper training and knowledge have been
obtained.
4.
Do not use this turret mill for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
5.
Always wear approved safety glasses/face
shields while using this turret mill. Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.
6.
Before operating this turret mill, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Do not wear loose
clothing. Confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
7.
Wear ear protectors (plugs or muffs) during
extended periods of operation.
8.
CALIFORNIA PROPOSITION 65 WARNING:
This product contains chemicals known to the
State of California to cause cancer, or birth
defects or other reproductive harm.
9.
This product, when used for welding, cutting, or
working with metal, produces fumes, gases, or
dusts which contain chemicals known to the
State of California to cause birth defects and, in
some cases, cancer. (California Health and
Safety Code Section 25249.5 et seq.)
10. Do not operate this machine while tired or under
the influence of drugs, alcohol or any
medication.
11. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance
14. Remove adjusting keys and wrenches. Form a
assembly
or
15. Keep safety guards in place at all times when
16. Check damaged parts. Before further use of the
17. Do not use power tools in damp/wet locations
18. Do not expose them to rain. Provide for
19. Keep the floor around the machine clean and
20. Keep visitors a safe distance from the work
21. Give your work undivided attention. Looking
22. Maintain a balanced stance at all times so that
23. Use the right tool at the correct speed and feed
24. Use
25. Maintain tools with care. Keep cutters sharp
26. Turn off the machine before cleaning. Use a
5
with the machine unplugged from the power
source.
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
or other dangerous environments.
adequate space surrounding work area and
non-glare, overhead lighting.
free of scrap material, oil and grease.
area. Keep children away. Workshop should be
child proof with padlocks, master switches or by
removing starter keys.
around, carrying on a conversation and "horse-
play" are careless acts that can result in serious
injury.
you do not fall against cutters or other moving
parts. Do not overreach or use excessive force
to perform any machine operation.
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
recommended
accessories;
accessories may be hazardous.
and clean for the best and safest performance.
Follow instructions for lubricating and changing
accessories.
brush or compressed air to remove chips or
debris — do not use your hands.
improper
Advertisement
Table of Contents
