BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 Installation and Setting-Up Instructions Contents: INSTALLATION Mounting location s. 2 Installing the transmitter s. 3 Dimensions of the transmitter s. 5 Electrical connections s. 6 SETTING-UP Setting-up with Satron VoAdvisor Service Software s.
Page 2
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 1. INSTALLATION 1.1 Mounting location Installation recommendations: Figure 1-1 transmitters should be installed as a general rule turbulence fl ow. Recommended installation location An alternative mounting location The mounting angle of the coupling 15°...
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 1.2 Installing the transmitter 1.2 I tallin th tr itte Ensure that the installation valve is clean from process media which could dam- age the transmitter prior to inserting the transmitter into it.
Page 4
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 Turn the installation tool level until the transmitter is fully inserted into the process. Fasten the transmitter in place with the locking nut E, Tightening torque 40Nm. Remove the installtion tool.
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 1.2 Electrical connections Position selection 3 x 90° Supply voltage and load of the transmitter according to the Figure 1-10. We recommend shielded twisted-pair cable as signal cable. The signal cable should not be installed near high- 1.
Setting-up with Satron-VoAdvisor Service Software When you want to have all the operations of the Smart transmitter, we recommend the use of Satron-VOadvisor Service Software program. Satron Instruments Inc. will deliver you the program, HART-modem and HP-2133 Mini Note PC according the order.
Setting-up with remote unit. The Satron VC transmitter remote unit can be provided with a wall box which is capable of having a 20m cable between the Sensing unit and the Display unit. Inside the Display unit is a terminal where up to 3 binary inputs, 3 relay outputs and 2 analog milliamp loops can be connected.
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 3. USER GUIDE FOR MENUS Under the main menu are 6 submenus: Confi guration, New Sample, Calibration, Diagnostics and Advanced. To enter these submenus press ESC for 3 seconds. The user interface for the series VO analyzers, housing option N, consists of display and operating keys.
Page 11
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 MANUFACTURER: MANUFACTURER: MANUFACTURER: SETCLOCK: SETCLOCK: Manufacturer’s name. (SATRON) Cannot be changed. Aika ja pvm(pp.kk.vvvv -hh.mm.ss) asetukset DEVICE TYPE: HART: The type code of device. Cannot be changed Tässä valikossa tehdään Multidrop-toiminnan ase- tukset.
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 ERROR AL the digital output will change its state ERROR AL the digital output will change its state IO2 SOURCE: IO2 SOURCE: when there is an error The source for 2 nd mA out (PV,ST, ET, ...).
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 SAMPLES: SAMPLES: The history of the sample (10). Laboratory values input. TRB TRIM: The transmitter calibration factory units (FU). SAMPLE 01: Upload a sample 1. TRB ZERO measurement of zero Calibration of measurement by two points SAMPLE 09: LRW.TRIM...
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 Press the ENTER-button to store the alarm current value. Press the ESC-button to return to the Press the ESC-button to enter the menu. main measuring screen. Select CONFIGURATION and press the ENTER-button.
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 2-point calibration with water and one sample point Press the [ ]-button and select the sample point (SAMPL 01...09) for 1-point Press the ESC-button to enter the menu calibration and press the ENTER-button.
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 Insert the GAIN value with the Press the ESC-button to enter the menu. ] and ENTER-buttons, until up- per separator reaches the right end of display. Press the ENTER-button to store the GAIN value.
Page 18
BCs220AV SATRON VC Optical Consistency Transmitter Revision 2 15.10.2014 Table 1. The content of error word 1 (EW1=0…15) Description Error message Process value error Sensor temperature (ST) error Electronics temperature (ET) error RANGE ER Percentage of output under -10% or over 110% error...