Hilti DG150 Safety Sheet

PERSONAL PROTECTION EQUIPMENT (PPE)

PROTECTIVE HEARING SAFETY
GLOVES PROTECTION GLASSES

IMPORTANT - CONDUCT A RISK ASSESSMENT

Before you commence any work at your chosen work area, you should
undertake some preliminary hazard identification and risk control
precautions. Ideally more than one person should do this. This is
undertaken by:
1. Physically inspecting the work site
2. Reviewing the best way/job steps required to complete the task
3. Reviewing the Safe Work Information supplied with the equipment
4. Reviewing other reference documentation and expert advice.
The hazard identification and control process steps are defined as:
1. Identify the Hazards (eg. 240V power drill use around wet areas)
2. Assess the Risk (multi earth paths - possible electrocution)
3. Select the Control Measure (e.g. dry the area; use an RCD; use a
cordless drill etc)
3 Description
4. Re-assess the Risk (risk of electrocution now negligible). This is

3.1 Product overview

undertaken to ensure that the risk control measures adopted have not
introduced any new risks to the work area.

MAIN COMPONENTS

Diamond cup wheel
$ W
Lamellar seal, small
£ E
Clamping flange
| R
Lamellar seal, large
¡ T
Retaining ring
Q Z

3.3 Tool components, status indicators and controls

6 English
LED indicator
U Ü
Supply cord
I [
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
Locating lug
O ]
Carrying handle
P

3.4 Intended use

The product described is an electrically powered diamond grinder. It is designed for professional use in
Grinding mineral materials. The DG 150 grinder can be operated only in combination with the DPC 20 power
conditioner. Always use a dust extractor to ensure optimum dust removal.
The grinder is designed exclusively for dry abrasive removal of uncoated mineral materials and thin coatings
on concrete and similar mineral materials, with a maximum layer thickness of 3 mm (0.12 in).

3.5 Possible misuse

Do not use the product may in environments where there is a risk of explosion.
Do not use the product for wet grinding.
Do not use the product to work on hazardous or flammable materials (e.g. asbestos, magnesium, wood).
RESPIRATORY PROTECTIVE
PROTECTION HELMET

3.2 Tool components and controls

Arbor
Locking ring
Guard bottom section
Guard top section
Arbor lockbutton
Clip for power cord
Electrical socket with hinged cover
Latching lug
Pin wrench
:
8 English
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
DIAMOND GRINDER
3.2 Tool components and controls
HELP AND SUPPORT
If the unit does not operate correctly or you are unhappy with its
performance, return it to Asset Construction Hire for an exchange,
or phone for assistance. Do not attempt repairs yourself.
Asset Construction Hire
Phone:1300 361 383 or email: office@assethire.com.au
OPERATION MANUAL
PROTECTIVE
A PDF of the full Operation Manual is available at:
BOOTS
www.assethire.com.au/manuals-specs-safety-sheets/
and must be read before using the equipment.
BEFORE OPERATING THE EQUIPMENT:
• Read this Safety Sheet and any other information provided with the
equipment, including instructions, decals and operation guidelines.
• Check that you understand how and when the use the equipment,
and know how to operate it safely.
• Ensure that it is only used according to the manufacturers and hirer's
instructions, and only for work that is compatable with its technical
limitations.
• Operate in a clear work area free from nonessential persons, children,
animals or hazards.
• Ensure that you have a secure footing and clear access and egress to
the work area while on the job.
• Do not operate any equipment if you are tired or suffering any medical
condition, or if under the influence of drugs or alcohol which may
cause lethargy or dangers to yourself or others.
• Do not use faulty equipment. If in doubt contact Asset Construction Hire.
Diamond cup wheel
On/off switch
$
@
Lamellar seal, small
Side handle
£
;
Clamping flange
Guard, complete
|
=
Lamellar seal, large
Clamping band
¡
%
Retaining ring
Clamping lever
Q
&
Pin wrench
3.3 Tool components, status indicators and controls
:
8 English
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
Diamond cup wheel
$
Lamellar seal, small
£
Clamping flange
|
Lamellar seal, large
¡
Retaining ring
Q
3.3 Tool components, status indicators and controls
Clamping nut
∙
LED indicator
U
Supply cord
I
Locating lug
O
Carrying handle
P
SAFETY SHEET
(Hilti DG150)
3.2 Tool components and controls
PLEASE READ THIS GUIDE CAREFULLY
BEFORE OPERATING THE EQUIPMENT
On/off switch
@
Diamond cup wheel
Side handle
$
;
Lamellar seal, small
Guard, complete
£
=
Clamping flange
Clamping band
|
%
Lamellar seal, large
Clamping lever
¡
&
Retaining ring Arbor
LED indicator
Q W
(
Locking ring
Machine supply plug
E
)
Guard bottom section
Speed selector switch (speeds 1 and 2)
R 3.3 Tool components, status indicators and cont
+
Guard top section
Side-handle locking screw
T
§
Arbor lockbutton
Adjusting screw
Z
/
Pin wrench
:
Clamping nut
∙
Diamond cup wheel
$
8 Lamellar seal, small English
£
Clamping flange
|
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
Lamellar seal, large
¡
Retaining ring
Q
Arbor
W
Locking ring
E 3.3 Tool components, status indicators and cont
Guard bottom section
R
Guard top section
T
Arbor lockbutton
Z
LED indicator
U
Supply cord
I
Locating lug
O
Carrying handle
P
Clip for power cord
Ü
Electrical socket with hinged cover
[ 3.4 Intended use
Latching lug
]
The product described is an electrically powered di
grinding mineral materials. The DG 150 grinder can b
conditioner. Always use a dust extractor to ensure op