Related Manuals for E+E Elektronik EE23
Summary of Contents for E+E Elektronik EE23
- Page 1 Operation Manual EE23 Humidity/Temperature Sensor BA_EE23_B2_e // v1.0 // technical data are subject to change // 194768...
- Page 2 E+E Elektronik Ges.m.b.H. doesn’t accept warranty and liability claims neither upon this publication nor in case of improper treatment of the described products. The document may contain technical inaccuracies and typographical errors. The content will be revised on a regular basis. These changes will be implemented in later versions. The described products can be improved and changed at any time without prior notice.
-
Page 3: Table Of Contents
Connection Versions ...........................12 Calibration / Adjustment ........................14 5.1 Definitions ..............................14 Adjustment of EE23 Model T1, T2, T4 and T6 via Push Buttons on the Electronics Board ......14 5.2.1 2-Point RH Adjustment Procedure / T Adjustment Procedure ................14 5.2.2 1-Point RH Adjustment Procedure / T Adjustment Procedure ................15 5.2.3... -
Page 4: General
The operation manual may not be used for the purposes of competition without the written consent of E+E Elektronik® and may not be forwarded to third parties. Copies may be made for internal purposes. All information, technical data and diagrams included in these instructions are based on the information available at the time of writing. -
Page 5: Environmental Aspects
Environmental Aspects Products from E+E Elektronik® are developed and manufactured observing of all relevant requirements with respect to environment protection. Please observe local regulations for the device disposal. For disposal, the individual components of the device must be separated according to local recycling regulations. -
Page 6: Operating Components
- flashes during normal operation - continuously on indicates sensor damage 4. Push-Buttons The S1 and S2 push buttons are used for the EE23 adjustment as well as for returning to the factory calibration (see Calibration / Adjustment). 5. Level / Hysteresis Potentiometers for setting the threshold / hysteresis (available with alarm module only) -
Page 7: Display For Model T1, T2, T4 And T6
(with alarm module only). visual feedback when depressing the S2 push button (Fig. 1) 3. SET Indication for EE23 with optional alarm output 4. Td / Tf Dew point temperature / frost point temperature 5. -
Page 8: Electronic Board For Model T5
--> Error category 1 = non-critical error, can be solved by the user flashing --> Error category 2 = critical error, return the device for service Blue LED constantly lit --> analogue output is set to voltage. Orange LED constantly lit --> analogue output is set to current. 3. Interface: USB-Interface for service use Operating manual EE23 humidity / temperature sensor... -
Page 9: Display For Model T5
Return the faulty unit for service Temperature measurement failure ERROR: 07 ERROR: 09 Humidity measurement failure ERROR: 10 1) not available with 0 - 1 V output 2) see “Cleaning Instructions” at www.epluse.com/ee23 Tab. 2 Description of error messages on the display Operating manual EE23 humidity / temperature sensor... -
Page 10: Intallation
5. Place the front cover onto the middle part and close tight the enclosure using the four screws included in the scope of supply. Drilling for round holes: Drilling for long holes: Fig. 5 Mounting of metal enclosure Fig. 6 Mounting of polycarbonat enclosure Operating manual EE23 humidity / temperature sensor... -
Page 11: Mounting The Sensing Probe
T1 Wall mount T2 Duct mount Mounting onto DIN rails EE23 with polycarbonate enclosure can be mounted also on DIN rails with the bracket HA010203 (not included in the scope of supply, see “spare parts / accessories”). Mounting the Sensing Probe Whenever possible place the entire probe inside the space to be monitored. -
Page 12: Electrical Connection
1) Two M16x1.5 cable glands (one of them mounted onto the enclosure) 2) Power supply + analogue outputs: cable connector, 5-poles, straight M12 (Lumberg RKC 5/7) 3) Analogue output: cable connector, 5-poles, straight M12 (Lumberg RKC 5/7) 4) AC power supply: cable connector, 3-poles, straight (7/8ʺ-16UN) Operating manual EE23 humidity / temperature sensor... - Page 13 The protection of the supply cable against excess current and short-circuit must be designated to a wire cross section of 0.8mm² (AWG 18) (6A fuse). The back cover and the middle part of the metal enclosure must be grounded during operation! Operating manual EE23 humidity / temperature sensor...
-
Page 14: Calibration / Adjustment
1-point adjustment shall be performed at 50 % RH and 20 °C (68 °F). 1-point adjustment leads to very good accuracy within the range of main interest at the cost of the accuracy beyond this range. Adjustment of EE23 Model T1, T2, T4 and T6 via Push Buttons on the Electronics Board 5.2.1 2-Point RH Adjustment Procedure / T Adjustment Procedure 1. -
Page 15: 1-Point Rh Adjustment Procedure / T Adjustment Procedure
Press BUTTON S2 for min. 3 seconds to exit adjustment procedure without storing the adjusted value. In both cases the LED „D1“ and the symbol „CAL“ on the LC display are deactivated. 5.2.3 Return to Factory Calibration To return to RH or T factory calibration set first the jumper to RH or to T respectively. During normal measuring mode (i.e. not during the adjustment procedure. LED D1 shall be off, the display shall not show “CAL”) pressing BUTTON S1 and S2 together for min 5 seconds. The return to factory calibration is confirmed by a short flash of the LED „D1“. Operating manual EE23 humidity / temperature sensor... -
Page 16: Adjustment Of The Ee23 Model T5 Via The Usb Service Interface
Adjustment of the EE23 Model T5 via the USB Service Interface 1. Download and install the EE-PCS Product Configuration Software from www.epluse.com/configurator 2. Connect the USB service interface of EE23-T5 to the PC. 3. Start the EE-PCS software. 4. Select the desired adjustment mode and follow the instructions of the EE-PCS. -
Page 17: Accessories And Spare Parts
T5 D05P-EE23T5 - Mounting flange for probe diameter 12 mm HA010201 - Mounting flange 5mm (for model T6 only) HA010208 - Bracket for plastic enclosure - for installation onto mounting rails HA010203 - Drip water protection HA010503 - Calibration set HA0104xx (see data sheet „Calibration Kit“) - Radiation shield HA010502 Operating manual EE23 humidity / temperature sensor... -
Page 18: Technical Data
1) The accuracy statement includes the uncertainty of the factory calibration with an enhancement factor k=2 (2-times standard deviation). The accuracy was calculated in accordance with EA-4/02 and with regard to GUM (Guide to the Expression of Uncertainty in Measurement). 2) only for models T1, T2, T4 and T6. Operating manual EE23 humidity / temperature sensor... -
Page 19: Operating Range Humidity Sensor
Operating Range Humidity Sensor Temperature [degC] The gray area shows the allowed measurement range for the humidity sensor. Operation beyond this range does not destroy the sensing element, but the specified measurement accuracy cannot be guaranteed. Operating manual EE23 humidity / temperature sensor... - Page 20 HEADQUARTERS SUBSIDIARIES E+E Elektronik Ges.m.b.H. E+E Elektronik Germany E+E Elektronik France E+E Elektronik Korea Langwiesen 7 info@epluse.de info@epluse.fr Tel: +82 31 732 6050 A-4209 Engerwitzdorf Tel: +33 4 74 72 35 82 info@epluse.co.kr Office Bad Homburg Austria Tel: +49 6172 13881-0...