Antari HZ-500 User Manual

Antari HZ-500 User Manual

Haze machine
Hide thumbs Also See for HZ-500:

Advertisement

HZ-500
Haze Machine User Manual
English
Français
Deutsch
中文
© 2014 Antari Lighting and Effects Ltd.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HZ-500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Antari HZ-500

  • Page 1 HZ-500 Haze Machine User Manual English Français Deutsch • • • 中文 © 2014 Antari Lighting and Effects Ltd.
  • Page 3: Danger Of Electric Shock

    ANTARI HZ-500 HAZE MACHINE Introduction Thank you for choosing the ANTARI HZ-500 Haze Machine. You now own a rugged and powerful state-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the best, virtually invisible haze effect and reliable, satisfactory performance of your ANTARI HZ-500 Hazer for years to come.
  • Page 4 This product is for use on a nominal 120-V circuit and has a grounding plug similar to the plug illustrated in sketch A in the following Figure. Only connect the product to an outlet having the same configuration as the plug. Do not use an adapter with this product. Use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that accepts the plug on the product.
  • Page 5: Unpacking And Inspection

    1. Place the unit on a flat surface. Plug the power cord into a grounded electrical outlet. 2. Remove the fluid tank cap and pour the ANTARI Haze Liquid into the tank slowly and carefully to avoid overfilling. (Filling suggestion: Please add 2 liters haze liquid in the first time of refill. From the second refill on, add 1 liter haze liquid for every refill.) Make sure the liquid level does not...
  • Page 6 OK, plug the unit in again. If the hazer still does not function, discontinue operation or it may result in permanent damage to the unit. Return the machine to your Antari dealer. Always drain tank before mailing or transporting this unit.
  • Page 7: Control Panel Operation

    FUNCTION, Up, Down, TIMER, VOLUME and MANUAL. You can program the necessary menu settings with the control panel when the display indicates »Ready To Haze«. After switching on, the display shortly indicates »Antari Hz-500« and is ready for haze output. The display indicates »Ready To Haze«.
  • Page 8 The display indicates the set time interval. The unit counts down to 0 seconds and emits haze. To deactivate the timer mode, press the button TIMER again. -Menu settings with the button FUNCTION Setting time intervals for timer operation Press the button FUNCTION until the display indicates »Interval Set«. Use the buttons UP and DOWN to adjust the intervals between the individual fog outputs in timer mode within the range of 1 and 200 seconds.
  • Page 9: Dmx Connector Pin Assignment

    *Note 3: If the displays shows »Out Of Order«, the machine's internal temperature is too high and as a result the thermostat has been set off to shut-down the hazer. If you experience this problem, please check two points as described below: 1.
  • Page 10: Dmx Control Operation

    HZ-500 has on-board DMX control and the addressing is via the LCD control panel. The HZ-500 uses 1 channel to control on/off operation. The channel has a value range from 0 to 255. The on/off function can also be programmed with a DMX controller or DMX control software used by lighting and effects operator.
  • Page 11: Technical Specifications

    Technical Specifications Model: HZ-500 Power supply: 100-120V / 220-240V AC, 50/60Hz~ Nominal power consumption: 400 W 3,000 cu’ft’/min., Output volume: 105 m³/min. Tank capacity: 2.5 liters Fluid consumption: 20 hrs/liter Weight: 31.5 kg...

Table of Contents