Fluke 700HTP-2 Instruction Sheet

How to Prime the Test Pump
Before you connect the Pump to the Unit Under Test (UUT), the
Pump must be filled with fluid and primed for use. Follow the
directions below to prepare the Pump for use.
1. Fill the Pump with fluid:
a. Remove the Reservoir Filler Cap (item .)
b. Fill the Hydraulic Fluid Reservoir approximately two-thirds full
(66 cc) with distilled water, mineral oil, or hydraulic oil.
If water is used in the Pump, use only DISTILLED water
and drain the water out of the Pump after use.
c. Install the Reservoir Filler Cap (item .) Tighten by hand.
2. Prime the Pump:
a. Adjust the Vernier Fine Adjustment Knob (item ) to the
approximate middle-range.
b. Turn the Pressure Bleed Knob (item ) clockwise until it
stops in the full closed position.
c. Squeeze the handles together to pump fluid. Pump fluid until
fluid shows at the Pump Port.
d. Attach the fluid hose to the Pump.
e. Squeeze the handles together until fluid shows at the end of
the hose.
f. Attach the fluid hose to the Unit Under Test (UUT) and
squeeze the Pump handles until pressure increases.
g. Bleed the trapped air from the Pump. Pressurize the Pump to
1,000 psi then slowly turn the Pressure Bleed Knob (item )
counter-clockwise to release pressure.
• As the pressure rises it will be hard to squeeze the
handles together. Use the Handle Limiter (item
limit the travel of the handles which will make them
easier to squeeze together. To toggle the Handle
Limiter on or off, squeeze the handles together and
push the Handle Limiter (item
• The rate at which the pressure increases is directly
related to the test configuration (hose length and
volume of UUT.)
Replacement Parts
Rebuild Kit, Fluke PN 4097836
Hydraulic Fluid Reservoir Rebuild Kit, Fluke PN 2844341
Handle Assembly Rebuild Kit, Fluke PN 2844352
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for
one year from the date of purchase. This warranty does not cover fuses,
disposable batteries, or damage from accident, neglect, misuse, alteration,
contamination, or abnormal conditions of operation or handling. Resellers are
not authorized to extend any other warranty on Fluke's behalf. To obtain
service during the warranty period, contact your nearest Fluke authorized
service center to obtain return authorization information, then send the product
to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING
FROM ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or limitation of an implied warranty or of incidental or
consequential damages, this limitation of liability may not apply to you.
11/99
info@Fluke-Direct.com
Note
Notes

) to

) in or out.
Fluke-Direct
Fluke-700HTP-2
Hydraulic Test Pump
Introduction
The Fluke 700HTP-2 Hydraulic Test Pump (the Pump or Product) is a
portable source of high pressure.
Safety
W Warning
To prevent personal injury, use the Product only as
specified, or the protection supplied by the Product can be
compromised.
Pump Specifications
• Maximum pressure: 10,000 psi (690 bar)
• Hydraulic media: distilled water, mineral based hydraulic oil, or up
to hydraulic oil 100 (30 W).
• Wetted materials: 303 stainless steel, aluminum, polyurethane,
PTFE, nitrile, and nylon.
• Weight: 1.29 lb (0.58 kg)
• Dimensions: length 9.5 in (241 mm), width 6.1 in (155 mm), depth
2.6 in (66 mm)
Box Contents
• Model 700HTP-2 Hydraulic Test Pump with a 1/4-inch NPT tee
installed.
• Two 1/4-inch NPT male to 1/4-inch BSP female adapters.
• One 1/4-inch NPT male to 1/4-inch NPT male fitting.
• One 1/4-inch NPT male to 1/8-inch NPT male fitting.
• Instruction Sheet
PN 4096896
September 2011
2011 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
.com
Instruction Sheet
1.888.475.5235