Kit Contents
RayClic-PC Power Connection Kit
Item Qty Description
A
1
Power connection
B
1
Pipe mounting bracket
C
2
Plastic cable ties
G
1
Cable lubricant
RayClic-PS Powered Splice Kit
Item Qty Description
A
1
Powered splice
B
1
Pipe mounting bracket
C
2
Plastic cable ties
G
1
Cable lubricant
RayClic-PT Powered Tee Kit
Item Qty Description
A
1
Powered splice
B
1
Pipe mounting bracket
C
2
Plastic cable ties
G
1
Cable lubricant
This component is an electrical device that must be
installed correctly to ensure proper operation and to
prevent shock or fire. Read these important warnings
and carefully follow all the installation instructions.
• To minimize the danger of fire from sustained electrical
arcing if the heating cable is damaged or improperly
installed, and to comply with the requirements of Tyco
Thermal Controls, agency certifications, and national
Item Qty Description
D
1
Clip
E
1
End seal
F
4
Labels
(1 HWAT, 1 De-Icing &
Snow Melting, 2 Warning)
Item Qty Description
D
2
Clips
E
2
End seals
F
4
Labels
(1 HWAT, 1 De-Icing &
Snow Melting, 2 Warning)
Item Qty Description
D
3
Clips
E
3
End seals
F
4
Labels
(1 HWAT, 1 De-Icing &
Snow Melting, 2 Warning)
electrical codes, ground-fault equipment protection
must be used. Arcing may not be stopped by conven-
tional circuit breakers.
• Bus wires will short if they contact each other. Keep
bus wires separated.
• Keep components and heating cable ends dry before
and during installation.
RayClic Connection System
RayClic-PC Power Connection and End Seal Kit
RayClic-PS Powered Splice and End Seal Kit
RayClic-PT Powered Tee and End Seal Kit
Installation Instructions
Description
These kits are for use with Raychem IceStop, XL-Trace and HWAT heating
cables. The connection is designed to be strapped to the pipe or mounted
on the wall at the start of the heating cable circuit. These installation
instructions should be used in conjunction with the IceStop, XL-Trace
and HWAT System Installation and Operation Manuals. For technical
support, contact your Tyco Thermal Controls representative or call Tyco
Thermal Controls (800) 545-6258.
Tools Required
• Utility knife
• TORX
T20 screw driver
®
Additional UL Listed or CSA Certified materials required:
• 1/2-inch conduit and fittings
Optional Accessories (not included in this kit):
• RayClic-SB-02 Wall mounting bracket
Approvals
718K Pipe Heating Cable
877Z De-Icing and Snow Melting
Not UL Listed with XL-Trace
heating cable for buried piping.
For HWAT, IceStop, and XL-Trace only
Hazardous Locations: For IceStop (GM-XT) only
APPROVED
Class I, Div. 2, Groups A,B,C,D
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
• The black heating cable core is conductive and can
short. It must be properly insulated and kept dry.
• Component approvals and performance are based on
the use of Tyco Thermal Controls-specified parts only.
Do not use substitute parts or vinyl electrical tape.
• Leave these instructions with end user for reference
and future use.
• Wire cutters
• Wrenches (2)
• Junction box
-w
C
D
E
F
C
D
E
F
C
D
E
F
C
D
E
F
C
D
E
F
C
D
E
F
C
D
E
F
C
D
E
F
C
D
E
F
G
G
G
G
G
G
G
G
G