Table of Contents
Advertisement
Quick Links
L-SERIES CLUTCHES
INSTALLATION INSTRUCTIONS
(for L32, L32 PLUS, L40, L40 PLUS,
and L45, L45 PLUS Clutches)
L-SERIES CLUTCHES
INSTALLATION INSTRUCTIONS
Thank you for purchasing your new L-Series Clutches. They
have been custom-made from the highest quality materials.
to the dimensions you specified. With the proper installation
and care, it will provide you with many years of beauty and
trouble-free use.
Please read all instructions before you start so you will be
familiar with the overall process.
Make sure you measure your window to ensure the clutches
and shades will fit properly before beginning.
Getting Started
Remove the clutch and shade from the packaging. Keep the
packaging until you have successfully installed the clutch and
the shade.
TOOLS REQUIRED
• Pencil
• Awl
• Tape Measure
• Level
• Ladder or Stepstool
FASTENER NOTES
For outside mount, it is best to attach the bracket to wood
studs. If this is not possible, you will need to purchase special
fasteners (see illustration below for examples).
Molly Bolt
Here are some HELPFUL TIPS:
• If you are using a special fastener, make sure it is
designed to support the weight of the clutch and shade.
Follow the fastener manufacturer's instructions carefully.
• When drilling into drywall or plaster, use a fastener
designed for hollow wall applications (see illustration).
• When drilling into concrete, stone, brick, or tile, use
appropriate plugs, anchors, or screws (not included).
• When drilling into metal, the included screws are sufficient.
Pre-drill ¹⁄₈" holes.
1
5
- page
of
-
• Power Drill with the following bits:
- ¹⁄₁₆" Drill Bit
- ¹⁄₄" Hex Driver
- Standard Screwdriver
- Masonry Drill Bit (if drilling into
concrete or brick)
Hollow Wall Anchor
Anchor
Advertisement
Table of Contents
Related Manuals for Fabritec designs L32
Summary of Contents for Fabritec designs L32
-
Page 1: Getting Started
• If you are using a special fastener, make sure it is designed to support the weight of the clutch and shade. (for L32, L32 PLUS, L40, L40 PLUS, Follow the fastener manufacturer’s instructions carefully. and L45, L45 PLUS Clutches) •... - Page 2 L32 SERIES CLUTCHES STEP 3 - SET THE LOWER LIMIT /STOP POSITION. (This applies to L32 and L32 PLUS Clutches) Lower the shade to the desired long point. Then pinch the bead chain at this point on the front of the Mounting the Shade and Clutch clutch, and place one of the bead chain stops here.
- Page 3 L40 SERIES CLUTCHES STEP 2 - INSTALLING THE SHADE (continued). (This applies to L40, L40 PLUS, L45 & L45 PLUS Clutches) c. Slip the CCO end into the bracket. While keeping the idler end in position, lift the shade up Mounting the Shade and Clutch into the bracket and align the CCO end pin into the middle of the cross shaped hole.
- Page 4 STEP 4 - ADD THE END CAPS FOR A FINISHED LOOK. Note: The end caps cannot be used on an inside mount installation. STEP 5 - INSTALL THE P-CLIP (HOLDDOWN). Depress the p-clip holddown and firmly attach to the wall. DO NOT PULL THE BEAD CHAIN TAUT, as this will prevent the bead chain from operating smoothly.
- Page 5 L-SERIES CLUTCHES DETAILED DIAGRAM Bracket Cover Bracket (CCO end) Clutch Tube Chain Holddown Idler Bracket (Idler end) Bracket Cover Shade Round Hem Bar, optional FRONT VIEW (Room side) IMPORTANT! 1. Please read installation instructions first (included with hardware). 2. The brackets should be 1³₈” wider than the cloth width. 3.
Need help?
Do you have a question about the L32 and is the answer not in the manual?
Questions and answers