Related Manuals for Crown GLTS-30
Summary of Contents for Crown GLTS-30
- Page 1 INSTALLATION AND OPERATION MANUAL GAS SKILLETS MODELS: GLTS-30 GLTS-40 WWW.SOLARISSTEAM.COM PART NUMBER 10100R4 2005-10-14...
-
Page 2: Important Notes For Installation And Operation
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 IMPORTANT NOTES FOR INSTALLATION AND OPERATION This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. -
Page 3: Table Of Contents
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 TABLE OF CONTENTS DESCRIPTION PAGE Important Notes for Installation and Operation ................2 1.0 Service Connections ......................2.0 Installation Instructions ....................... 5 3.0 Operation Instructions ......................9 4.0 Periodic Maintenance ....................... 12 5.0 Cooking Guidelines ...................... -
Page 4: Service Connections
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 1.0 SERVICE CONNECTIONS PART NUMBER 10100R4 2005-10-14... -
Page 5: Installation Instructions
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 2.0 INSTALLATION INSTRUCTIONS UNPACKING Immediately after unpacking, check for possible shipping damage. If the tilting braising pan is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. - Page 6 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 INSTALLATION CODES AND STANDARDS Installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1INFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1, as applicable.
- Page 7 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 2.0 INSTALLATION INSTRUCTIONS (Continued) LEVELLING AND ANCHORING 1. Set the appliance in place and level left to right and front-to-back using spirit level. 2. Mark hole locations on floor through anchoring holes provided in flanged adjustable feet.
- Page 8 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 2.0 INSTALLATION INSTRUCTIONS (Continued) WARNING: Never use an open flame to check for gas leaks. Check all connections for leaks using soapy water before use. After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.
-
Page 9: Operation Instructions
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 3.0 OPERATION INSTRUCTIONS Do not attempt to operate this unit in the event of a power failure. BEFORE FIRST USE Using a non-corrosive, grease-dissolving commercial cleaner, clean the protective metal oils from all surface parts and the interior of the tilting braising pan. - Page 10 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 3.0 OPERATION INSTRUCTIONS (Continued) START-UP PROCEDURE 1. Open manual gas shutoff valve. 2. Ensure that the braising pan is in the DOWN position. 3. Turn on power switch. 4. Turn THERMOSTAT dial to desired setting. The red TEMPERATURE LIGHT will come on.
- Page 11 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 3.0 OPERATING INSTRUCTIONS (Continued) TILTING THE BRAISING PAN 1. DO NOT try to tilt braising pan with lid down. 2. Make sure the receiving pan is in place. 3. To tilt braising pan, push and hold TILT SWITCH in the UP mode until desired pan position has been reached.
-
Page 12: Periodic Maintenance
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 4.0 PERIODIC MAINTENANCE WARNING: Disconnect the power supply to the appliance before cleaning or servicing. CAUTION: Do not use cleaning agents that are corrosive. CAUTION: Operating, testing, and servicing should only be performed by qualified personnel. - Page 13 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 4.0 PERIODIC MAINTENANCE (Continued) CAUTION: The appliance and its parts are hot. Use care when operating, cleaning and servicing the appliance. WARNING: Disconnect the power supply to he appliance before cleaning or servicing.
-
Page 14: Cooking Guidelines
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 5.0 COOKING GUIDELINES The guidelines given below are suggested quantities, temperature settings, and estimated numbers of orders per load and per hour. When two temperatures are given, the first is to start the product, and the second to finish the product. - Page 15 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 BATCHES GLTS-30 GLTS-40 PORTION TEMP. PER LOAD PER LOAD ITEM SIZE (°F) QTY. PORTIONS QTY . PORTIONS HOUR Haddock Fillet 4 oz. 60 - 4 oz. 90 - 4 oz. Halibut Steak 5 oz.
- Page 16 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 BATCHES GLTS-30 GLTS-40 PORTION TEMP. PER LOAD PER LOAD ITEM SIZE (°F) QTY. PORTIONS QTY . PORTIONS HOUR Corn 3 oz. 15 lbs. 22-½ lbs. Small Whole 3 oz. 15 lbs.
- Page 17 INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS: GLTS-30, GLTS-40 BATCHES GLTS-30 GLTS-40 PORTION TEMP. PER LOAD PER LOAD ITEM SIZE (°F) QTY. PORTIONS QTY . PORTIONS HOUR PORK Ham Steak 3 oz. 10 lbs. 15 lbs. Pork Chops 5 oz.
-
Page 18: Troubleshooting
INSTALLATION AND OPERATION MANUAL, GAS SKILLETS, MODELS GLTS-30, GLTS-40 6.0 TROUBLESHOOTING Burners do not come on: 1. Gas supply to unit is “OFF”. 2. Manual shut off valve is “OFF”. 3. Thermostat is not turned “ON”. 4. Pan not in lowest position.