ORiNG IBS-102FX Quick Installation Manual

ORing Industrial Networking Corp.
BYPASS
SWITCH
Q I
uick nstallation
I N D U S T R I A L

Introduction

IBS-102FX Series is an external Bypass switch for 100M/1G/10G fiber optical
networks. This fiber optical bypass switch protects from network failures and
Network maintenance by ensuring network integrity during power loss. This fiber
optical bypass switch includes Network ports and Monitor ports.
are used to connect to main-network connections and provide protection mechanism
local
and the Monitor ports are used for down-link
is on, the mode of the Bypass switch is in Normal operation mode and the local
networking device is connected with main-network. When on the power failure state,
the Bypass switch is set to bypass mode to isolate the main-network from the
local networking device .

Features

Support 100M/1G/10G optical bypass function of 2 port duplex or 4 port simplex
fiber connection
Different model supported for multi-mode or single-mode optical fiber
Low insertions loss
Throughput not affected and no extra delay
Bypass switching time <10ms
Dual Wide range power inputs: 12~48VDC
Relay output for pwer failed warning
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled

Power Connection Guide

1A@24V PWR2 PWR1
- +
Relay V+ V- DC12-48V
V-
Power2
V+
Supply
12-48 VDC
Warning
Device
+24V GND
Power
Supply
Q I G
IBS-102FX
G
uide

Specifications

ORing Bypass Switch Model
The Network ports
Physical Ports
networking device. When power LC connector
Fiber Ethernet
Optical Fiber
Operating Wavelength
Insert loss
Switching time

DIP Switch Setting

DIP-Swicth No.1
DIP-Switch No.2

LED Indicators

Power indicator
Normal indicator
Fault Indicator
Fault contact
Relay
Power
Input power
Power consumption (Typ.)
Overload current protection
Reverse Polarity

Physical Characteristic

Enclosure
Dimension (W x D x H)
G
Frame Ground
Weight (g)

Environmental

Storage Temperature
Power1 Input 12-48VDC
Operating Temperature
Operating Humidity

Regulatory approvals

EMI
EMS
Shock
Free Fall
Vibration

Warranty

1907-2-29-IBS102FX-0
IBS-102FX
IBS-102FX-SS-LC IBS-102FX-MM-LC
4 Duplex Single-mode LC 4 Duplex Multi-mode LC
connector connector
Single-mode: 9/125 m µ Multi-mode: 50/125µm or 62.5/125µm
1260 ~ 1570 nm 780 ~ 1350 nm
typical1.2 dB , Maximun 1.6 dB < 1.0 dB
< 10ms
Power-1 failed warning detection: (On) relay enabled (Off ) relay disabled
Power-2 failed warning detection: (On) relay enabled (Off ) relay disabled
Green : power LED x 2.
Green On : Operated in normal mode
Amber for power failed indicator
Relay output to carry capacity of 1A at 24 VDC
Dual 12~48 VDC power inputs at DC-Jack and 4-pin terminal block
2.7 Watts
Present
Present on Terminal Block
IP-30
26.1(W)x94.9(D)x144.3(H) mm (1.03x3.74x5.68inch.)
405g
o o
-40 to 85 C (-40 to 185 F)
o o
-20 to 70 C (-4 to 158 F)
5% to 95% Non-condensing
FCC Part 15, CISPR (EN55022) class A
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT),
EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
IEC60068-2-27
IEC60068-2-32
IEC60068-2-6
1 years
PRINTED ON RECYCLED PAPER
Industrial Optical Bypass Switch

Practical Operation

Normal mode: Bypass mode:
The Bypass switch deliver the data The Network data traffic routed directly
between the Network ports and the to the other Network port. And the Monitor
Monitor (local) ports data traffic routed directly to the other
Monitor port.
IBS -102FX
P1 P2 Fault
Alarm
P1
P2
TX
A
RX
TX
B
RX
TX
A
RX
TX
B
RX
Nomal mode
100M /1G /10G bps
ORing Industrial Networking Corp.
Copyright© 2011 ORing
All rights reserved.
TEL: +886-2-2918-3036 Website: www.oring-networking.com
FAX: +886-2-2918-3084 E-mail: support@oring-networking.com
Quick Installation Guide
Version 1.0
Bypass mode