Advertisement
2.2 Verify that the Apple iPod touch device has connected to
the wireless router. You should see wireless signal strength
indicator bars in the top-left corner of the Apple iPod touch
device main screen (see Figure 1 below).
Note: This connection may take some time to be
established. You should not proceed until the indicator
bars appear (see Figure 1 below).
2.3 Run the Energi Savr Node (ESN) setup application by
touching the icon (see Figure 1 below).
2.4 When the application loads, you should see the connected
Energi Savr Node unit.
Figure 1. Main Screen of iPod touch device
Wireless signal strengh indicator bars
Step 3: Set up the system
Note: Only follow these instructions when setting up
a system for the first time. For a system that is already
operational and needs minor adjustments, Ballast
Addressing is NOT generally required; simply navigate
to existing areas and modify the settings as needed.
3.1 Connect to the device (for help during any part of the
set-up process, use the on-screen help button as shown in
Figure 2 below)
• S elect the desired Energi Savr Node unit and connect to it.
• W hen prompted, enter a password. You will need
this password when connecting to the device to make
configuration changes in the future.
Figure 2. on-Screen Help Button of Energi Savr Node
Setup Application
?
On-Screen
Help Button
technical and Sales Assistance
If you need assistance, call the toll-free Lutron Technical Support Center.
Please provide the programming kit model number when calling: C-ESN-SETUP.
U.S.A. / Canada / Caribbean: 1.800.523.9466
Mexico: +1.888.235.2910
Other Countries: +1.610.282.3800
Visit our web site at www.lutron.com
Lutron, EcoSystem and the sunburst logo are registered trademarks and Energi Savr Node is a trademark of Lutron Electronics Co., Inc.
Apple and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Lutron Electronics Co., Inc | 7200 Suter Road | Coopersburg, PA 18036-1299 USA
3.2 Navigate to the configuration screen
• F rom the Home screen, navigate to System setup >
3.3 Verify wiring
• N avigate to the Verify wiring screen and ensure that all
3.4 Address ballasts
• I f programming an EcoSystem
3.5 Create areas
• U sing the Setup areas screen, create new areas that
3.6 Define areas
• W ithin the Setup areas screen, perform the following
Energi Savr Node
setup application
icon
3.7 Program controls
• R eturn to the Home screen. Navigate to System setup
• P rogram any IR sensors, QS keypads, Grafik Eye
3.8 Program dry contact inputs
• P rogram any configurable dry contact inputs on the Energi
Step 4: Start Saving energy with your
Energi Savr Node System!
Configure an ESN. Select the desired ESN and touch
Next to see the main configuration screen.
ballasts/outputs are responding correctly to the system
commands.
(QSN-2ECO-S, QSN-1ECO-S), address the ballasts by
navigating to the Address ballasts screen.
correspond to the areas that you want to control in
your space (e.g. hallway, office).
steps for each area that you created.
— Navigate to the Define lights in this area screen
and identify which lights belong to each area.
— If programming an EcoSystem Energi Savr Node unit
(QSN-2ECO-S, QSN-1ECO-S), navigate to the
Setup zones/scenes screen to define the lighting
zones that should exist in each area and assign the
appropriate lights from the area to each zone as
desired. Other Energi Savr Node models (such as
QSN-4S16-S and QSN-4T16-S) have zones that are
already pre-defined.
— Also on the Setup zones/scenes screen, configure
the desired area scenes by modifying the scene
names as desired and specifying the zone light levels
for each scene.
— If desired, navigate to the Setup daylighting screen
and program the daylighting behavior by assigning
daylight sensors to each area, defining the daylight rows
in each area, and calibrating the daylighting settings.
— If desired, navigate to the Setup occupancy screen
and program the occupancy behavior by assigning
occupancy sensors to each area and specifying the
occupied and unoccupied scenes.
to view the various device programming options.
units, or other QS devices to control the Energi Savr
Node unit lighting as desired using the Program devices
and Program IR sensors screens.
Savr Node units using the Program ESN inputs screen.
Energi Savr Node unit
®
QS
®
032-344a 11/10
Advertisement
