ABB REC650 Product Manual page 17

Bay control REC650 2.2
Product version: 2.2
• Line for double and transfer busbars, ABC_LINE
• Bus coupler for double and transfer busbars, ABC_BC
• Transformer bay for double busbars, AB_TRAFO
• Bus-section breaker for double busbars, A1A2_BS
• Bus-section disconnector for double busbars, A1A2_DC
• Busbar earthing switch, BB_ES
• Double CB Bay, DB_BUS_A, DB_LINE, DB_BUS_B
• 1 1/2-CB diameter, BH_LINE_A, BH_CONN, BH_LINE_B
Switch controller SCSWI
The Switch controller (SCSWI) initializes and supervises all
functions to properly select and operate switching primary
apparatuses. The Switch controller may handle and operate
on one multi-phase device or up to three one-phase devices.
Circuit breaker SXCBR
The purpose of Circuit breaker (SXCBR) is to provide the
actual status of positions and to perform the control
operations, that is, pass all the commands to primary
apparatuses in the form of circuit breakers via binary output
boards and to supervise the switching operation and position.
Circuit switch SXSWI
The purpose of Circuit switch (SXSWI) function is to provide
the actual status of positions and to perform the control
operations, that is, pass all the commands to primary
apparatuses in the form of disconnectors or earthing switches
via binary output boards and to supervise the switching
operation and position.
Reservation function QCRSV
The purpose of the reservation (QCRSV) function is primarily
to transfer interlocking information between IEDs in a safe
way and to prevent double operation in a bay, switchyard
part, or complete substation.
Reservation input RESIN
The Reservation input (RESIN) function receives the
reservation information from other bays. The number of
instances is the same as the number of involved bays (up to
60 instances are available).
Bay control QCBAY
The Bay control (QCBAY) function is used together with Local
remote and local remote control functions to handle the
selection of the operator place per bay. QCBAY also provides
blocking functions that can be distributed to different
apparatuses within the bay.
Proxy for signals from switching device via GOOSE
XLNPROXY
The proxy for signals from switching device via GOOSE
(XLNPROXY) gives an internal representation of the position
status and control response for a switch modelled in a
breaker IED. This representation is identical to that of an
SXCBR or SXSWI function.
ABB
M13486-3 v10
M13489-3 v6
M16492-3 v6
M13506-3 v5
M16501-3 v5
M13447-3 v8
GUID-11F9CA1C-8E20-489B-822B-34DACC59553A v1
GOOSE function block to receive a switching device
GOOSEXLNRCV
The GOOSE XLN Receive component is used to collect
information from another device's XCBR/XSWI logical node
sent over process bus via GOOSE. The GOOSE XLN Receive
component includes 12 different outputs (and their respective
channel valid bits) with defined names to ease the 61850
mapping of the GOOSE signals in the configuration process.
Local remote LOCREM/Local remote control LOCREMCTRL
The signals from the local HMI or from an external local/
remote switch are connected via the function blocks local
remote (LOCREM) and local remote control (LOCREMCTRL)
to the Bay control (QCBAY) function block. The parameter
ControlMode in function block LOCREM is set to choose if
the switch signals are coming from the local HMI or from an
external hardware switch connected via binary inputs.
Logic rotating switch for function selection and LHMI
presentation SLGAPC
The logic rotating switch for function selection and LHMI
presentation (SLGAPC) (or the selector switch function block)
is used to get an enhanced selector switch functionality
compared to the one provided by a hardware selector switch.
Hardware selector switches are used extensively by utilities,
in order to have different functions operating on pre-set
values. Hardware switches are however sources for
maintenance issues, lower system reliability and an extended
purchase portfolio. The selector switch function eliminates all
these problems.
Selector mini switch VSGAPC
The Selector mini switch (VSGAPC) function block is a
multipurpose function used for a variety of applications, as a
general purpose switch.
VSGAPC can be controlled from the menu, from a symbol on
the single line diagram (SLD) on the local HMI or from Binary
inputs.
Generic communication function for Double Point indication
DPGAPC
Generic communication function for Double Point indication
(DPGAPC) function block is used to send double point
position indications to other systems, equipment or functions
in the substation through IEC 61850-8-1 or other
communication protocols. It is especially intended to be used
in the interlocking station-wide logics.
Single point generic control 8 signals SPC8GAPC
The Single point generic control 8 signals (SPC8GAPC)
function block is a collection of 8 single point commands that
can be used for direct commands for example reset of LEDs
or putting IED in "ChangeLock" state from remote. In this
way, simple commands can be sent directly to the IED
outputs, without confirmation. Confirmation (status) of the
result of the commands is supposed to be achieved by other
1MRK 511 426-BEN B
GUID-5AC7DE11-CB95-4565-A8AE-FB23D59FD717 v1
M17086-3 v10
SEMOD114908-4 v11
SEMOD158756-5 v10
SEMOD55850-5 v7
SEMOD176462-4 v11
17