Avaya Scopia XT5000 Quick Setup Manual

Setting Up this Device
Connect the cables as detailed in the diagram overleaf, then follow the steps below to complete
the setup of the Avaya Scopia XT Camera Switch. For details on how to use the system after
setup, see the User Guide for Avaya Scopia XT Series or the Quick Start Guide for Avaya Scopia
XT Series.
Step 1. System Installation
Place the Avaya Scopia XT Camera Switch on a horizontal surface
close to the XT Codec Unit. Maximum supplied cable length is
40cm (0.13ft).
Step 2.
Connect one end of the HDMI cable to the OUTPUT socket on
1.
the Scopia XT Camera Switch
- On the XT5000 Codec Unit, connect the other
end to the available HDMI input.
- On XT7000 Codec Unit, connect the other
end to the HDMI2 input.
Connect one end of the USB cable to the USB socket on the
2.
Avaya Scopia XT Camera Switch and the other end to the upper
USB connector on the XT Codec Unit.
4 3 2 1
Avaya Scopia XT5000
HDMI USB
Codec Unit
4 3 2 1
Avaya Scopia XT7000
HDMI USB
Codec Unit
Step 3.
Check that the SYSTEM SELECT switch on the back panel of each
camera is set to 7:
SYSTEM IR SELECT
DC IN 12V SELECT 1 2 3 IN RS-232C OUT DVI
Step 4.
Connecting the first camera
Insert the three connectors of the
camera cable (3 connectors on one side,
2 connectors on the other side) to the
sockets on the back of the camera:
The DVI connector to the DVI socket.
1.
The 8-pin connector to the
2.
IN RS232C socket.
DC IN 12V SYSTEM SELECT IR SELECT 1 2 3 IN RS-232C OUT
The power connector to the
3.
DC IN 12V socket.
Step 5.
Attach the two connectors on the other end of the camera cable:
On XT5000 Series, connect the On XT7000 Series, connect the
1.
HDMI connector to the HDMI first camera directlyto the HDMI1
socket labeled 1 on the Scopia port of the codec, as in single
XT Camera Switch. camera setup.
DC IN 12V SYSTEM SELECT IR SELECT 1 2 3 IN RS-232C OUT DVI
1
2. The connector for power and serial control to the horizontal
socket on the XT Codec Unit.
CAUTION:
Make sure all units are
switched off whenever connecting
or disconnecting devices.
Step 6.
Connect the second camera as follows:
Connect the 10-meter VISCA Control cable supplied with the
1.
camera kit:
Attach one end of the VISCA control cable to the
a.
IN RS-232C connector on the second camera.
Attach the other end to the OUT RS-232C
b.
connector on the first camera.
Connect the DVI-HDMI cable as follows:
2.
Attach the DVI connector to the DVI
a.
socket on the second camera.
On XT5000, Attach the HDMI connector to the HDMI socket
b.
labeled 2 on the Scopia XT Camera Switch.
On XT7000, Attach the HDMI connector to the HDMI socket
labeled 1 on the Scopia XT Camera Switch.
Connect one end of the power supply cable to the DC IN 12V
3.
connector on the camera, and the other end into one of the
power sockets on the wall.
Second Camera
4 2 3 1 1 1
1 2
SYSTEM IR SELECT
DC IN 12V SELECT 1 2 3 IN RS-232C OUT DVI
1
XT Camera Switch
Connected to XT5000
2
XT Camera Switch
Connected to XT7000
Step 7.
If required, repeat the above step for a third or fourth camera.
Step 8.
Switch on the Scopia XT5000 or
1.
DVI XT7000 unit, the cameras and the
XT Camera Switch.
Set Configure > General > Show
2.
Advanced Settings to Yes
Set Configure > Advanced > I/O
3.
Connections > Cameras >
General > XT Camera Switch
detect mode = Yes.
(default PIN for Advanced configuration is 1234)
Step 9.
Setup each camera in the GUI
1.
section
Configure > Advanced > I/O
Connections > Cameras
as explained in the "Deployment
Guide for XT Series".
Avaya Scopia

Quick Setup Guide

First Camera
SYSTEM IR SELECT
DC IN 12V SELECT 1 2 3 IN RS-232C OUT DVI
Avaya Scopia XT Camera Switch
enables all the endpoints of Avaya
Scopia XT5000 and XT7000 series
to be connected with up to four
HD Cameras or four generic HDMI
devices (such as DVD and generic
media players). The Avaya Scopia XT
Camera Switch is fully powered and
controlled from the Avaya Scopia
XT endpoint. The switch can be
controlled from XT User Interface
and Remote Control.
XT Camera Switch
®

Package Content:

•
Avaya Scopia XT Camera Switch
•
Cable USB 40cm
•
Cable HDMI M/M, 40cm