Samsung SCX-6545N Series User Manual page 110

MESSAGE MEANING
There is a problem in
Finisher error: [zzz].
the finisher unit.
Please turn off then
on
There is a problem in
Fuser error: [zzz].
the fuser unit working.
Please turn off then
on
The fuser unit is not
Fuser unit is not
installed or correctly.
installed correctly.
Install it
The toner in the
Imaging unit is
imaging unit has run
empty. Replace it
out.
The imaging unit you
Imaging unit is not
have installed is not
compatible. Check
for your machine.
user's guide
The imaging unit is
Imaging unit is not
not installed, or the
installed. Install it
CRUM (Consumer
Replaceable Unit
Monitor) in the
cartridge is not
connected.
The imaging unit is at
Imaging unit is
the end of its life.
worn. Replace with
When the imaging unit
new one
replacement message
appears on the screen
and if you select
Continue, this
message displays.
There is a problem in
LSU error: [zzz].
the control of LSU
Please turn off then
unit.
on
There is a problem in
Motor does not
the control of motor
operate: [zzz].
unit.
Please turn off then
on
The lead edge of the
Original paper does
document failed to
not feed in scanner
actuate the scan
sensor within the
correct time after
actuating the
registration sensor.
109 _Troubleshooting
SUGGESTED
SOLUTIONS
Turn the machine off
and reinstall the finisher
again. Check that the
finisher cable is
connected properly. If
the problem persists,
please call for service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for service.
Install the fuser unit.
Call for service.
Replace the imaging
unit with a Samsung-
genuine toner cartridge.
(See "Replacing the
imaging unit" on
page 97.)
Install a Samsung-
genuine imaging unit,
designed for your
machine.
Install the imaging unit.
If it is already installed,
try to reinstall the
imaging unit.
If the problem persists,
please call for service.
Replace a imaging unit
with a Samsung-
genuine imaging unit.
(See "Replacing the
imaging unit" on
page 97.)
Turn the machine off
and turn it on again. If
the problem persists,
please call for service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for service.
Open the DADF cover
and remove jammed
original. (See "Clearing
document jams" on
page 100.)
MESSAGE MEANING
Oversized document
Original paper is too
or double-feeding of
long for scanner.
originals.
Check size
The originals are
Original paper jam
jammed in DADF.
in front of scanner
Paper has jammed
Original paper jam
during duplex printing
in front of scanner
in the DADF.
duplex path
The lead edge of the
Original paper jam
document failed to
inside of scanner
actuate the gate
sensor within the
correct time after
actuating the scan
sensor.
When the machine is
on, jammed paper is
detected in the DADF.
The lead edge of the
Original paper jam
document failed to
while reversing
actuate the duplex
paper in scanner
sensor within the
correct time when the
document was fed the
wrong way.
Paper jammed in the
Paper jam at exit of
stacker exit part.
finisher
Paper has jammed
Paper Jam at the
during duplex printing.
bottom of duplex
path
Paper Jam at the top
of duplex path
Paper has jammed in
Paper Jam in exit
the fuser area.
area
Paper jammed in the
Paper jam in front of
stacker.
finisher
Paper jam inside
finisher
SUGGESTED
SOLUTIONS
Open the DADF cover
and remove the
jammed original. (See
"Clearing document
jams" on page 100.)
Check the document
size whether it is
supported. (See "DADF
document size" on
page 126.)
Open the DADF cover
and remove the
jammed original. (See
"Clearing document
jams" on page 100.)
Clear the jam. (See
"Clearing document
jams" on page 100.)
Open the DADF cover
and remove the
jammed original. (See
"Clearing document
jams" on page 100.)
Lift up the document
input tray and remove
the jammed original.
(See "Clearing
document jams" on
page 100.)
Pull jammed paper
from the stacker exit.
Clear the jam. (See "In
the duplex unit area" on
page 107.)
Clear the jam. (See "In
the fuser area or
around the toner
cartridge" on
page 106.)
Open the stacker door
and remove jammed
paper by lowering
guide 1a or 1b.