Mitsubishi Electric PAR-SL100A-E Installation Manual page 8

Function selection procedure
First, it is important to understand the procedure for the function selection. The following procedure explains how to set "LOSSNAY connectivity" in
WDEOH  WR 6XSSRUWHG LQGRRU XQLW LV QRW HTXLSSHG ZLWK RXWGRRUDLU LQWDNH DV DQ H[DPSOH
For the actual operations, refer to the following procedure.
B
6
3
Fig. 6-3
Unit
Fig. 6-4
1. Press the
,I WKH ZHHNO\ WLPHU LV HQDEOHG
A
off).
button 2 for 5 seconds.
2. Press the
A FRPHV RQ DQG WKH XQLW HQWHUV WKH VHOIFKHFN PRGH
‡
button 6 to set the displayed number B to "50".
3. Press the
‡ While pointing the wireless remote controller toward the receiver, press the
4 7KH XQLW QXPEHU EOLQNV
button 6 to set the unit number of the indoor unit. (Fig. 6-3)
4. Press the
‡ While pointing the wireless remote controller toward the receiver, press the
1
4 7KH PRGH QXPEHU EOLQNV
* When the unit number is transmitted, the selected indoor unit starts operating in the fan
mode.
You can use this step to confirm which indoor unit corresponds to the unit number you
selected to change the functions.
2
However, if you set the unit number to "00" or "AL", all of the indoor units in the same
4
refrigerant system will start operating in the fan mode.
* If you transmit a unit number that cannot be selected, the beeper sounds 3 times con-
5
WLQXRXVO\ ³EHHS EHHS EHHS      VHF ´
If this occurs, press the
QXPEHU GLVSOD\ LV EOLQNLQJ
* If the signal was not received correctly, the beeper will not sound or it will beep twice.
If this occurs, press the
QXPEHU GLVSOD\ LV EOLQNLQJ
button 6 to set the mode number. (Fig. 6-3)
5. Press the
‡ While pointing the wireless remote controller toward the receiver, press the
4 7KH VHWWLQJ QXPEHU EOLQNV
$W WKLV WLPH WKH EHHSHU VRXQG DQG 23(5$7,21 ,1',&$725 ODPS EOLQNLQJ SDWWHUQ LQGL
cate the current setting number for the selected mode number.
&XUUHQW VHWWLQJ YDOXH
Mode
,I \RX HQWHU D PRGH WKDW FDQQRW EH VHW WKH EHHSHU VRXQGV  WLPHV FRQWLQXRXVO\ ³EHHS
Setting
beep, beep (0.4 + 0.4 + 0.4 sec.)".
If this occurs, press the
PRGH QXPEHU GLVSOD\ LV EOLQNLQJ
* If the signal was not received correctly, the beeper will not sound or it will beep twice.
If this occurs, press the
PRGH QXPEHU GLVSOD\ LV EOLQNLQJ
button 6 to select the setting number. (Fig. 6-3)
6. Press the
‡ While pointing the wireless remote controller toward the receiver, press the
4 7KH PRGH QXPEHU EOLQNV
$W WKLV WLPH WKH EHHSHU VRXQG DQG 23(5$7,21 ,1',&$725 ODPS EOLQNLQJ SDWWHUQ LQGL
cate the setting number for the selected mode number.
&XUUHQW VHWWLQJ YDOXH
* If you enter a number that cannot be set, the originally set number will be used.
* If the signal was not received correctly, the beeper will not sound or it will beep twice.
If this occurs, repeat the procedure from step 5.
7. To set another mode without changing the unit number of the indoor unit, repeat steps 5 and
6.
8. To change the unit number of the indoor unit and perform the function selection, repeat
steps 4–6.
9. Press the
Note:
$IWHU WKH IXQFWLRQ VHOHFWLRQ LV FRPSOHWH GR QRW RSHUDWH WKH ZLUHOHVV UHPRWH FRQWURO
ler for 30 seconds.
:KHQHYHU WKH IXQFWLRQ VHOHFWLRQ LV XVHG WR FKDQJH WKH LQGRRU XQLW IXQFWLRQV DIWHU
LQVWDOODWLRQ EH VXUH WR UHFRUG DOO RI WKH VHWWLQJV ZLWK D ³ ´ RU RWKHU PDUN LQ WKH ³,QL
WLDO VHWWLQJ´ FROXPQ RI WKH WDEOH
button 1 to stop the air conditioner.
is on), press the
button 5, and then set the unit number again while the unit
button 5, and then set the unit number again while the unit
 %HHS  VHF î  WLPH
 %HHS  VHF î  WLPHV
 %HHS  VHF î  WLPHV
button 5, and then set the mode number again while the
button 5, and then set the mode number again while the
 %HHS  VHF î  WLPH
 %HHS  VHF î  WLPHV
 %HHS  VHF î  WLPHV
button 1 to complete the function selection.
button 3 to disable it (
is
button
button
button
button
8