Mitsubishi Electric PAR-SL100A-E Installation Manual page 5

BH79J525H01
6 Service
3
Fig. 6-1
B
3
5
Fig. 6-2
5HIHU WR WKH IROORZLQJ WDEOHV IRU GHWDLOV RQ WKH FKHFN FRGHV
* A receiver adapter (MA type) cannot be used.
[Output pattern A]
Beeper sounds Beep
OPERATION
INDICATOR
ODPS EOLQNLQJ
Off
pattern
Approx. 2.5 sec.
6HOIFKHFN
starts
(Start signal
1XPEHU RI EOLQNVEHHSV LQ SDWWHUQ LQGLFDWHV WKH FKHFN
received)
FRGH LQ WKH IROORZLQJ WDEOH LH Q  IRU ³3´
[Output pattern B]
Beeper sounds Beep
OPERATION
INDICATOR
ODPS EOLQNLQJ
Off
pattern
Approx. 2.5 sec.
6HOIFKHFN
starts
(Start signal
received)
[Output pattern C]
Beeper sounds Beep
OPERATION
INDICATOR
ODPS EOLQNLQJ
Off
pattern
Approx. 2.5 sec.
6HOIFKHFN
starts
(Start signal
received)
1XPEHU RI EOLQNVEHHSV LQ SDWWHUQ LQGLFDWHV WKH FKHFN
FRGH LQ WKH IROORZLQJ WDEOH LH Q IRU ³(+´
6.1. Test run (Fig. 6-1)
1. Press the
‡ ,I WKH ZHHNO\ WLPHU LV HQDEOHG
B
off).
2. Press the
‡ comes on and the unit enters the service mode.
3. Press the
A
B comes on and the unit enters the test run mode.
‡
4. Press the following buttons to start the test run.
6ZLWFK WKH RSHUDWLRQ PRGH EHWZHHQ FRROLQJ DQG KHDWLQJ DQG VWDUW WKH WHVW UXQ
1
6ZLWFK WKH IDQ VSHHG DQG VWDUW WKH WHVW UXQ
6ZLWFK WKH DLUIORZ GLUHFWLRQ DQG VWDUW WKH WHVW UXQ
6ZLWFK WKH ORXYHU DQG VWDUW WKH WHVW UXQ
6WDUW WKH WHVW UXQ
2 5. Stop the test run.
‡ Press the
‡ After 2 hours, the stop signal is transmitted.
6.2. Self-check (Fig. 6-2)
1. Press the
‡ ,I WKH ZHHNO\ WLPHU LV HQDEOHG
A
is off).
2. Press the
A FRPHV RQ DQG WKH XQLW HQWHUV WKH VHOIFKHFN PRGH
‡
3. Press the
XQLW IRU ZKLFK \RX ZDQW WR SHUIRUP WKH VHOIFKHFN
4. Press the
‡ ,I DQ HUURU LV GHWHFWHG WKH FKHFN FRGH LV LQGLFDWHG E\ WKH QXPEHU RI EHHSV IURP WKH
1
LQGRRU XQLW DQG WKH QXPEHU RI EOLQNV RI WKH 23(5$7,21 ,1',&$725 ODPS
5. Press the
A and the refrigerant address (M-NET address) B JR RII DQG WKH VHOIFKHFN LV FRP
‡
pleted.
2
4
Beep Beep Beep Beep
1 st 2 nd 3 rd n th
On On On On
0.5 sec. 0.5 sec. 0.5 sec.
0.5 sec.
Beep Beep
1 st 2 nd
On On On
Approx. 3 sec. 0.5 sec. 0.5 sec.
1XPEHU RI EOLQNVEHHSV LQ SDWWHUQ LQGLFDWHV WKH FKHFN
FRGH LQ WKH IROORZLQJ WDEOH LH Q  IRU ³8´
Beep Beep Beep Beep
st nd rd th
1 2 3 n
%OLQNV %OLQNV %OLQNV
%OLQNV
2 times 2 times 2 times
2 times
0.3 sec.×2 0.3 sec.×2 0.3 sec.×2 0.3 sec.×2
button 1 to stop the air conditioner.
is on), press the
button 2 for 5 seconds.
button 2.
button 1 to stop the test run.
button 1 to stop the air conditioner.
is on), press the
button 2 for 5 seconds.
button 5 to select the refrigerant address (M-NET address) B of the indoor
button 4.
button 1.
Beep Beep
1 st 2 nd · · · Repeated
Off On On
Approx. 2.5 sec. 0.5 sec. 0.5 sec.
1XPEHU RI EOLQNVEHHSV LQ SDWWHUQ LQGLFDWHV
WKH FKHFN FRGH LQ WKH IROORZLQJ WDEOH
Beep Beep
3 rd n th
On On Off
0.5 sec. 0.5 sec. Approx. 2.5 sec.
Beep Beep
st nd
1 2 · · · Repeated
Off %OLQNV %OLQNV
2 times 2 times
Approx. 2.5 sec.
0.3 sec.×2 0.3 sec.×2
1XPEHU RI EOLQNVEHHSV LQ SDWWHUQ LQGLFDWHV
WKH FKHFN FRGH LQ WKH IROORZLQJ WDEOH
button 3 to disable it (
button 3 to disable it (
Beep Beep
1 st
2 nd · · · Repeated
On On On
Approx. 3 sec. 0.5 sec. 0.5 sec.
1XPEHU RI EOLQNVEHHSV LQ SDWWHUQ LQGLFDWHV
WKH FKHFN FRGH LQ WKH IROORZLQJ WDEOH
is
5