WUX450 / WX520 / WUX400ST / WX450ST User Commands Table of Contents Table of Contents ......................ii 1. Overview ......................... 1 2. Communication Specifications ................. 2 Communication Specifications ......................2 Usable Character Codes ........................3 Communication System (Serial) ......................4 Communication System (LAN) ......................
WUX450 / WX520 / WUX400ST / WX450ST User Commands 1. Overview These specifications describe the methods of controlling Projector WUX450 / WX520 / WUX400ST / WX450ST from PC or other controllers over an RS232C connection or LAN. Symbol The following symbols are used in these specifications:...
WUX450 / WX520 / WUX400ST / WX450ST User Commands 2. Communication Specifications Communication Specifications The projector can be controlled via RS-232C or LAN connection. PC - Projector connection configuration LAN PORT LAN PORT Network Connection ネットワーク接続 プロジェクター PROJECTOR COM PORT...
WUX450 / WX520 / WUX400ST / WX450ST User Commands Usable Character Codes Use ASCII codes in the red and blue areas of below table. No distinction is made between double-byte characters and single-byte characters. Do not use double-byte or triple-byte characters. They will all be recognized as single-byte characters.
WUX450 / WX520 / WUX400ST / WX450ST User Commands Communication System (Serial) Item Specifications Communication system RS-232-C Start-stop synchronization Semi-duplex communication Transmission speed 19.2 Kbps Character length 8 bits / character Stop bit 2 bits Parity None Command format Variable-length records with terminals as delimiters Maximum transmission Maximum of 256 characters (bytes) including delimiters.
WUX450 / WX520 / WUX400ST / WX450ST User Commands Response Format Responses are sent from the projector to PC in the following format: <Response character string> <Delimiter> There are multiple response types, each having different <response string> format. <Response character Strings consisting of 1 or more alphanumeric letters string>...
Page 9
WUX450 / WX520 / WUX400ST / WX450ST User Commands Reference command response A response when reference is made properly for a reference command. Format) g:<command string>=<value><delimiter> <command string> Character strings consisting of 1 or more alphanumeric letters <value> Character strings consisting of 1 or more alphanumeric letters...
WUX450 / WX520 / WUX400ST / WX450ST User Commands Normal response (BUSY) This response is sent when a command cannot be received during processing. Format) i:BUSY<delimiter> Example) PC to PJ PJ to PC Other Command recognition The receiver (projector) retains incoming characters within a specific Tc, and recognizes the data as "received command"...
WUX450 / WX520 / WUX400ST / WX450ST User Commands 3. Communication Flow Command Transmission (PC side) Commands should be sent from PC in a way that each character is sent within the specified Tc (inter-character timeout) Command Reception (projector side) The receiver (projector) retains incoming characters within a specific Tc, and recognizes the data as "received command"...
WUX450 / WX520 / WUX400ST / WX450ST User Commands 5. Guide to command description This section explains how commands are described. The command descriptions have the format shown below. EXAMPLE Summary of the function Format Setting Command A command format when a command is sent to the projector to make a setting for the function.
Page 15
WUX450 / WX520 / WUX400ST / WX450ST User Commands Environment This defines the environments that support the command (power supply state, input signal state). The command is executable when the projector is in the mode indicated by "○" in the table of corresponding command description page.
WUX450 / WX520 / WUX400ST / WX450ST User Commands 6. Command Details 6AXADJ 6-axix adjustment / OFF Format Setting Command 6AXADJ=<6-axix adjustment parameter: ID> Response i:OK Reference Command GET=6AXADJ Response g:6AXADJ=<6-axix adjustment parameter: ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands AMBADJ Ambient light adjustment / OFF Format Setting Command AMBADJ=<Ambient light correction adjustment parameter:ID> Response i:OK Reference Command GET=AMBADJ Response g:AMBADJ=<Ambient light correction adjustment parameter:ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands AMBTYPE Ambient light type setting Format Setting Command AMBTYPE=<Ambient light type settings parameter:ID> Response i:OK Reference Command GET=AMBTYPE Response g:AMBTYPE=<Ambient light type settings parameter:ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands ASELD Digital PC Audio input terminal selection Format Setting Command ASELD=<Digital PC audio terminal selection parameter: ID> Response i:OK Reference Command GET=ASELD Response g:ASELD=<Digital PC audio terminal selection parameter: ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands ASPECT Aspect ratio Format Setting Command ASPECT=<Screen setting parameters: ID> Response i:OK Reference Command GET=ASPECT Response g:ASPECT=<Screen setting parameters: ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands AUTOSETEXE Auto setup Format Setting Command AUTOSETEXE=<Auto set parameter:ID> Response i:OK Reference Command Response Note: See "Error list" for any response other than the above. < Auto set parameter:ID > Parameter...
WUX450 / WX520 / WUX400ST / WX450ST User Commands BLANK BLANK setting Format Setting Command BLANK=<BLANK parameter:ID> Response i:OK Reference Command GET=BLANK Response g:BLANK=<BLANK parameter:ID> Note: See "Error list" for any response other than the above. < BLANK parameter:ID >...
WUX450 / WX520 / WUX400ST / WX450ST User Commands COLOR_TEMP Color temperature Format Setting Command COLOR_TEMP=<Color temperature setting:Number> Response i:OK Reference Command GET=COLOR_TEMP Response g:COLOR_TEMP=<Color temperature setting:Number> Note: See "Error list" for any response other than the above. Setting values for <Color temperature setting:Number> are -17 to 21.
WUX450 / WX520 / WUX400ST / WX450ST User Commands CONT Contrast Format Setting Command CONT=<Contrast setting:Number> Response i:OK Reference Command GET=CONT Response g:COMVER="<User command version:Character string> Note: See "Error list" for any response other than the above. Setting values for <Contrast setting:Number> are -20 to 20.
WUX450 / WX520 / WUX400ST / WX450ST User Commands DZOOM_POS DZOOM position setting Format Setting Command DZOOM_POS=<DZOOM position X:Number>,<DZOOM position Y:Number> Response i:OK Reference Command GET=DZOOM_POS Response g:DZOOM_POS=<DZOOM position X:Number>,<DZOOM position Y:Number> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands DZOOM_RAT DZOOM ratio setting Format Setting Command DZOOM_RAT=<DZOOM ratio parameter:ID> Response i:OK Reference Command GET=DZOOM_RAT Response g: DZOOM_RAT=<DZOOM ratio parameter:ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands Error information reference Format Setting Command Response Reference Command GET=ERR Response g:ERR=<ErrorID:Character string> Note: See "Error list" for any response other than the above. < DZOOM ratio parameter:ID > Parameter Meaning...
WUX450 / WX520 / WUX400ST / WX450ST User Commands FLTWRN Air filter cleaning warning Format Setting Command FLTWRN=<Filter warning parameter: ID> Response i:OK Reference Command GET=FLTWRN Response g: FLTWRN=<Filter warning parameter: ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands GAMMA Gamma adjustment Format Setting Command GAMMA=<Gamma adjustment:Number> Response i:OK Reference Command GET=GAMMA GAMMA=<Gamma adjustment:Number> Response Note: See "Error list" for any response other than the above. Setting values for <Gamma adjustment: Number> are -10 to 10.
WUX450 / WX520 / WUX400ST / WX450ST User Commands IMAGEFLIP Flip display Format Setting Command IMAGEFLIP=<Image flip setting parameters:ID> Response i:OK Reference Command GET=IMAGEFLIP Response g:IMAGEFLIP=<Image flip setting parameters:ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands KREP Key repeat Format Setting Command KREP=<Key repeat parameter: ID> Response i:OK Reference Command GET=KREP Response g:KREP=<Key repeat parameter: ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands LAMPCOUNTER Lamp counter reference Format Setting Command Response Reference Command GET=LAMPCOUNTER Response g:LAMPCOUNTER="<Lamp ON time:Character string> Note: See "Error list" for any response other than the above. < Lamp ON time:Character string >...
WUX450 / WX520 / WUX400ST / WX450ST User Commands MAIN Unit control panel emulation Format Setting Command MAIN=<Side control emulation button parameters:ID> Response i:OK Reference Command Response Note: See "Error list" for any response other than the above. < Side control emulation button parameters:ID >...
WUX450 / WX520 / WUX400ST / WX450ST User Commands MEMF Memory color adjustment (flesh) Format Setting Command MEMF=<Memory color adjustment parameter:ID> Response i:OK Reference Command GET=MEMF Response g:MEMF=<Memory color adjustment parameter:ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands MEMS Memory color adjustment (sky) Format Setting Command MEMS=<Memory color adjustment parameter:ID> Response i:OK Reference Command GET=MEMS Response g:MEMS=<Memory color adjustment parameter:ID> Note: See "Error list" for any response other than the above.
Page 48
WUX450 / WX520 / WUX400ST / WX450ST User Commands Noise reduction Format Setting Command NR=<Noise reduction setting parameter:ID> Response i:OK Reference Command GET=NR Response g:NR=<Noise reduction setting parameter:ID> Note: See "Error list" for any response other than the above. < Noise reduction setting parameter:ID >...
WUX450 / WX520 / WUX400ST / WX450ST User Commands POWER This controls the power supply Format Setting Command POWER=<power control parameter:ID> Response i:OK Reference Command GET=POWER Response g:POWER=<power mode parameter:ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands PRODCODE Product name inquiry Format Setting Command Response Reference Command GET=PRODCODE Response g:PRODCODE="<Product name:Character string> Note: See "Error list" for any response other than the above. < Product name:Character string >...
Page 51
WUX450 / WX520 / WUX400ST / WX450ST User Commands Remote control operation emulate Format Setting Command RC=<Remote control emulation button parameters:ID> Response i:OK Reference Command Response Note: See "Error list" for any response other than the above. < Remote control emulation button parameters:ID >...
WUX450 / WX520 / WUX400ST / WX450ST User Commands RGBGAIN RGB gain adjustment Format Setting Command RGBGAIN=<R gain setting:Number>,<G gain setting:Number>, <B gain setting:Number> Response i:OK Reference Command GET=RGBGAIN Response g:RGBGAIN=<R gain setting:Number>,<G gain setting:Number>, <B gain setting:Number> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands ROMVER Firmware version inquiry Format Setting Command Response Reference Command GET=ROMVER Response g:ROMVER="<ROM version:Character string> Note: See "Error list" for any response other than the above. Environment Power mode restriction Input...
WUX450 / WX520 / WUX400ST / WX450ST User Commands SIGNAL_INFO Inquires about displayed signal information Format Setting Command Response Reference Command GET=SIGNAL_INFO Response g:SIGNAL_INFO="<Input signal information:Character string> Note: See "Error list" for any response other than the above. Environment Power mode restriction...
WUX450 / WX520 / WUX400ST / WX450ST User Commands TEMP Temperature sensor value inquiry Format Setting Command Response Reference Command GET=TEMP Response g: TEMP=<Number of sensors>,<Sensor 1 value>,…,<Sensor n value> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands TPTN Test pattern Format Setting Command TPTN=<Test pattern parameter: ID> Response i:OK Reference Command GET=TPTN Response g:TPTN=<Test pattern parameter: ID> Note: See "Error list" for any response other than the above.
WUX450 / WX520 / WUX400ST / WX450ST User Commands 7. Error List Response Meaning Reaction The command was successfully i:OK processed. The command was invalid (not Use a correct command or correct command e:0002 INVALID_COMMAND defined), or the command format was format.