Related Manuals for Titon TP221T
Summary of Contents for Titon TP221T
- Page 1 Trimbox Mixed Flow Fans TP220T TP221T TP222T TP223T Product Manual ventilation systems...
-
Page 2: Safety Information
2. This manual covers the installation of the Titon In-Line Fans 3. All wiring must conform to current I.E.E. Wiring Regulations and all applicable standards and Building Regulations. - Page 3 11. The appliance is not suitable for installation to the exterior of the dwelling. 12. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental ca- pabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Page 4: Explanation Of Symbols On The Appliance 4
Explanation of symbols on the appliance. Read instruction Manual. Risk of Electric Shock. Isolate from the mains power supply before removing the cover. Contains rotating mechanical parts. Following isolation from the mains power supply allow sufficient time for all moving parts to stop before removing any ducting. -
Page 5: Table Of Contents
Contents Safety Information Important Information 2 Explanation of symbols on the appliance 4 Product Information Product Features 6 Packaging Contents 6... -
Page 6: Product Information
Product Information Titon In-Line Fans are designed to extract humid & stale air and expel it to the exterior. They are also suitable for extracting air from one room and expelling it to another room. The fan unit is usually fitted in the ceiling void, well away from the inlet. This In-Line feature allows the inlet grille to be mounted in wet areas (eg near the splash zones of bathrooms) or even above a shower. -
Page 7: Dimensions 7
Dimensions The diagram details the overall size of the unit. Installer must allow additional space around the unit to allow for future servicing and maintenance. Part Number TP220T TP221T TP222T TP223T Duct Diameter ID Ø100mm Ø125mm Ø150mm Ø160mm Dimensions mm ØA... -
Page 8: Component Identification 8
Component Identification Terminal Box Gromet INLET Impellor Fixing Holes Fixing The units are designed as in-line duct fans to be fitted between two duct runs. Choose a suitable mounting location for the inlet grille. Ensure there is adequate clearance for the ducting. Choose a suitable location for the extract grille ensuring there is adequate clearance for the ducting. -
Page 9: Ducting 9
The duct must not be installed vertically into a roof terminal - the product is not designed or intended for this type of installation. Ducting Titon recommend using rigid ducting, any flexible ducting used should be fully extended. All ducting joints must be fixed using a method that ensures a long term seal is... -
Page 10: Wiring 10
Wiring Access to the wiring terminals is via the terminal box on top of the unit. 220-240V~ TP 2xxT 50/60Hz... -
Page 11: Commissioning 11
Commissioning Overrun Timer The Overrun Timer is factory set to approximately 3 minutes. The Overrun Timer can be set between 3 and 30 minutes. Access to Overtime Timer Control is via the terminal box on top of the unit. WARNING: Unit uses a 220-240V~ supply and contains rotating mechanical parts. -
Page 12: Speed Setup 12
ISOLATE the unit from mains power supply and allow sufficient time for all moving parts to stop before Commissioning. The Titon Mixed Flow Fans runs at one of 3 speeds; Low [L]; Medium [M]; High [H]. The factory default is Medium. -
Page 13: Product Fiche 13
CO4 9YQ Model Ø100mm Trimbox Ø125mm Trimbox Mixed Flow In-line fan Mixed Flow In-line fan Model Identifier TP220T TP221T Declared Typology NRVU - UVU NRVU - UVU Type of Drive installed Multi-speed drive Multi-speed drive Type of heat recovery system... - Page 14 Static efficiency of fan in accordance with (EU) No 327/2011 33% - < 125W motor 33% - < 125W motor Declared maximum internal leakage rate (%) Energy performance of the filters Filter Warning (RVU) Internet address (for dissassembly instructions) www.titon.co.uk...
-
Page 15: Maintenance
Maintenance Routine Maintenance WARNING: The unit uses a 220-240V~ supply and contains rotating mechanical parts. ISOLATE the unit from mains power supply and allow sufficient time for all moving parts to stop before undergoing any Servicing or Maintenance. All ventilation units require periodic maintenance, units should be inspected and cleaned. - Page 16 Pack and used as a service record. Installed by: MARKETING DIVISION 894 The Crescent, Colchester Business Park, Colchester, CO4 9YQ Tel: +44 (0) 1206 713800 Fax: +44 (0) 1206 543126 Email: ventsales@titon.co.uk Web: www.titon.com ©2018 TITON DO 5581 Iss 02...
Need help?
Do you have a question about the TP221T and is the answer not in the manual?
Questions and answers