Advertisement
Digital Lock Set
Installation Instructions
2) Apply the Template
Select the desired position on the door. Fold the template on the dotted 60mm
backset line to suit the deadlatch assembly supplied.Tape the template to the door.
* Mark and drill six 10mm holes as shown on the template.
* Mark the central point on the "centre line of latch" on the edge of the door and
drill a 25mm hole to a depth of 85mm.
* Insert the latch into the latch holes and mark around the face plate.
* Remove the latch and cut a 3mm rebate so that the face plate fits flush with the
edge of the door.
* Fit the latch assembly with 2 wood screws. (Ensure that the bevelled face of
the latchbolt faces the door frame)
3) Handing the Digital Exterior Code
Pad Assembly
HANDLE
Rotation
4) Handing the Digital Interior Handle
Assembly
Hole A for left hand hung door
(HOLE A)
Rotation
and Hole B for right hand hung
BLACK HANDING
door.
SCREWS
To change for a left hand door:
* Remove BLACK handling
(HOLE B)
screw from hole A and
Hexagon Socket
relocate it in hole B.
Head Cap Screw
To change lever handle to suit
LEVEL
Interior Handle
Assembly
a left hand :
HANDLE
* Loosen the Hexagon Socket
Head Cap Screw located at the bottom of the spindle hub and
rotate the lever handle from right to left.
* Tightening the Hexagon Socket Head Cap Screw and make sure
the lever handle is horizontal.
Check correct lever handle function by turning handle from
horizontal position through 90° without resistance
6) Positioning the Spindles
Viewed from
the outside
DOOR HUNG ON RIGHT
SPINDLE SHOULD ENGAGE
THE LATCH AS ABOVE
Apply strength to rotate the handle to the
HANDLE
desired direction.
IMPORTANT: In order to change the left
and right hand of the lock handles correctly,
the lock must be mounted on the door.
5) Fit Latch Support Post
Fit the Latch Assembly
Support Post in the back
of the Digital Code Pad
B
A
Assembly. Hole A for left hand
hung door and Hole B for
right hand hung door.
Latchbolt
Support Post
Fit Hex screw post top and
Hex Screw
Post
bottom of external keypad.
Three spindles are provided. Select the
spindle length to suit the door thickness.
* For door thinknesses less than 35mm
use the shorter spindle (76mm). For
door thinknesses of 35-50mm use the
longer spindle (86mm) or (100mm).
* Position spindle centrally through the
latch hub to suit door handing as shown.
DOOR HUNG ON LEFT
SPINDLE SHOULD ENGAGE
THE LATCH AS ABOVE
Digital Lock Set
Installation Instructions
7) Mounting the Lock
Select the fixing screws to suit the door thinkness.
* For door thinknesses less than 48mm use the shorter fixing screws (36mm).
* Fit the neoprene seals to both the Exterior Code Pad and Interior
Handle Assemblies.
* Hold the Exterior Code Pad Assembly onto the door with the spindle
in position and ensuring that the latch support post engages the hole
in the latch assembly.
* Locate the Interior Handle Assembly on the inside of the door engaging
the spindle in the handle hub.
* Screw both sides together with fixing screws top and bottom. (FIG 1)
* Before tightening of fixing screws make sure the lock is vertical. Test the
mechanism to ensure that the lock functions correctly and moves easily.
NOTE: DO NOT overtighten the fixing screws-this may cause distortion and
lead to poor operation.
FIG 1
CHECK THAT THE CODE WORKS TO AVOID A LOCKOUT BEFORE
CLOSING THE DOOR.
8) Fitting the Strike Plate
Fig. 1
Fig. 2
* Close the door against the door frame and transfer the centre of the latchbolt onto the jamb.
* Position the strike plate on the door so that it fits against the flat of the latchbolt,with deadlatch pin depressed (Fig. 1).
* Close the door and mark the position of the strike plate on the door jamb.
* Using the strike plate as a template,align it with the position marks in the jamb and mark the inner and outer edges of
the strike plate on the jamb.(Fig 2).
* Cut a 1mm deep rebate so that the strike plate fits flush with door jamb(Fig 2).
* Drill and chisel out the latchbolt hole to accommodate the latch bolt strike box(Fig 3).
* Fit strike plate and strike box using only one wood screw at first to ensure that it is positioned accurately.
* The latchbolt and not the deadlatch pin should enter the strike plate aperture freely and engage without excessive play.
* When correctly positioned secure with the second wood screw and check lock set for smooth operation.
Digital Lock Set - Passage Mode Function
Passage Function - where fitted
TO SET PASSAGE MODE - FREE ACCESS AND EGRESS.
* Enter correct codes turn the handle of Digital Exterior Code Pad
Assembly to 6 o'clock position and hold the handle in downward
position.
passage knob
* Turn the passage knob of Digital Interior Handle Assembly from 12
o'clock to 9 o'clock "P" position. Release the handle and "Passage
Mode" is set. Then you do not need a code and you can open the door.
TO SET CANCEL PASSAGE MODE -
* Turn handle of Digital Exterior Code Pad Assembly to the 6 o'clock
position, followed by a passage knob of Digital Interior Handle
Assembly to the 12 o'clock position.
DEADLATCH
PIN
"LATCHBOLT"
Fig. 3
Advertisement
